It is not listed in model C parameter manual, but listed in model D manual.
Designated as NAL (probably implying No ALarm)
Type: Posts; User: sinha_nsit
It is not listed in model C parameter manual, but listed in model D manual.
Designated as NAL (probably implying No ALarm)
Normally EXT should have zero values.
However, it does not hurt it it has non-zero entries. Just make sure that these values are not changed.
Last one hour only.
Today is the last day for the FREE download of this book.
Please click the given link, and read the book description.
I am sure you will find it extremely useful for learning (if you are...
If you post the compete program (or its relevant part), somebody may be able to help you.
Discusses programming, tooling and operation of a Fanuc CNC lathe.
Offer valid for five days only, starting from today.
Available on ALL amazon sites.
Download link on amazon.com:...
I would request the admin to close this thread which was started by me some 15 years back.
Somehow, people are getting the impression that Fanuc NCGUIDE software is free and request for its...
Rough calculations:
Core dia = 13.4
Thread height = 1.2
OD = 13.4 + 2x1.2 = 15.8
First DOC = 0.3
First roughing X = 15.8 - 2x0.3 = 15.2
You are saying that it is 13.7
Please check if the...
Parameter 6030 should be 0 or 198
Parameter 0020 should be 4
File name on memory card should not have any extension
If some axis is disabled, it will not work even in memory mode.
If the same problem is there on similar machines, then possibly this function is not enabled. Contact MTB to find out.
There is no parameter to disable feedhold button.
Possibly, it is malfunctioning. Did it ever work earlier?
Are you doing rigid tapping?
So, the special character was not the issue.
Possibly, some specific format caused the problem. Or, maybe, some temporary issue with the site.
If I face this problem again, I will pm you.
It contained this special character
#
Let us see if it is accepted this time.
It was a copied text from the Word file of one of my books. IIRC, the server was throwing Error 503.
Maybe I did something wrong. Will be more careful next time.
Let us hope we meet some day over drinks!
I have a detailed answer, but the server is not allowing to post it. Don't know why.
If using "chamfering and corner rounding," set CCR to 0 and use I-K method.
Since only one forum member found the thread a bit inappropriate, there is no reason to delete it. He also will perhaps change his mind if he comes to know more about me.
So, let me introduce...
Ok.
I wanted to delete this message, but there seems to be no way. Mod may delete it.
Even editing is not possible.
May like to have a look ...
https://www.amazon.com/dp/B0CDCLSHWJ
The discounted price applicable today only. The regular price is $4.99
Paperback 11.99 and hardcover 19.99
It is a 480-page book.
** is not available in Fanuc as well.
Check if ** is available
Why do you have both C and H on the G84 block?
Why repeating M53?
Are you sure that rigid tapping is enabled on your machine?
It is not a very accurate statement. The arc starts with the start radius. If it cannot reach the target point due to some inaccuracy, it makes a small linear move in the end to reach the end point,...
May like to read this for detailed information on Fanuc 2-line G71/G72.
This is an option.
Follow the instructions in the manual. If EXEC softkey does not appear then the option is not activated on your machine.
Argument specification II uses A, B, and C once each. Apart from
these three letters, it uses I, J, and K up to 10 times each (i.e., 10 independent
sets of I, J, and K are used). Thus, it can pass...
May like to refer to this.