Now the machine is down and i cant get it back.not sure if it is relevant or not but in the diagnostic parameters page parameter 0054 has the 4 numbers on the left flashing between 0 and 1 as well as...
Type: Posts; User: kirby
Now the machine is down and i cant get it back.not sure if it is relevant or not but in the diagnostic parameters page parameter 0054 has the 4 numbers on the left flashing between 0 and 1 as well as...
I have an older fanuc controlled machine and for the last little while we have been having an intermittent issue. Someti.es when a tool is finished its program and it comes to clearance the machine...
What is the difference between the manual I have and the one you suggest. I would contact okuma and get the manual if there is vital information I don't have. My latest encounter with tech support is...
These are what I have. The U 10m is the book for the machine but only describes dnc-b with the rs232. The osp7000 book is the one that has the info for the...
It doesn't sound familiar... I have all the original manuals for the machine. I actually think this Ethernet connection is an early variation. So much so that okuma doesn't even know exactly what...
I don't believe. I will check in the morning
Sent from my SM-G930W8 using Tapatalk
Just to add to that....when we try to format the drive it takes roughly 5 minutes to get that alarm. If I remove the ssd completely I get the same alarm in about 10 seconds. We have tested that there...
Dnc t.... I was confused last time. My manual was for dnc b. But I have a special function manual for dnc t. When you push edit/aux and extend it is dnc t on the control. And yes I have the external...
What is with all the smiley faces? Are you 12. I don't get you. You first sentence should have been your last. You said I can't help you with your cnc. You should have moved on then.I don't need your...
It was a package deal from a university. They were closing the machine shop. All the equipment was unhooked. And trust me...it was a good deal. As for why I have not done anything with the machine it...
Hi guys....
I am still at this. I took some time off. Where I stand with it now is I believe the flash drive/ hard drive is gone or not working. I have no issues loading small programs from the Tc...
thanks....after I twisted my fat a** inside the machine I found the switches and one was stuck. Works fine now...
Thanks again...Kirby
next clue to the puzzle...
when I initiate a tool change and run the diagnostics I get msg "15728 magazine pot horizontal LS is not OFF" This is described in the book as: During ATC operation,...
couple more things...we can manually remove the tool from the spindle...
and the pot number does correspond correctly with the number in the parameters in the controller..
Hi All..
I am looking for a bit of help. We have a 2001 MC-V4020 with a tool changer issue. It wont change tools. It was working fine and then all of a sudden it just stopped changing. It will...
I have all the manuals...2 copies of each. I will have a look and see what i can find. Got a hint at which one or which section to look.
Also, where would i save the file CALL.SDF?
I think i...
This is what happens when i enter these commands. I am doing it in "auto operation mode" as that seemed to make sense as you push auto mode button...then program select...then type the above commands...
if i try to enter this i get " 300 device name error 'TC' "
my issue today is how do we copy a program from the TC: directory to the MD1: directory?
I somehow fluked it yesterday and i even managed to overwrite the program(totally by accident)
What we...
thanks for your help. We have actually made a bit of progress. I loaded a program from the computer( not sure how i did it and cant duplicate it but i did it) and we actually got it to run( a few...
what would you do to load the program at the controller? I have the Ethernet working and we have sent files back and forth between the controller and the computer. We are stuck at how to get from...
and just to clarify...the LAN cable is connected inside the main electrical panel to a port that says"LAN" not to the RS232 port..
also...what is DNC-B and how does it differ from DNC-T
i have DNC-B on my machine...i have rs232...i have a switch on the back that says buffer I/O but i am told i cant drip feed...
we are connected via a cable but not through RS232. Its a LAN cable. This machine was supposed to have the early version of ethernet.
We can see the program at the controller that is on the...
Hi All,
We recently purchased a new to us 2001 V4020 mill with a U10M control. Its a really nice machine for 2001. It has 2000 hours, 15000 rpm spindle, renshaw probe, 4th axis and a few other...
It was a simple fix. What happened was the timing belts that went from the spindle to the encoder were old and stretched. When the quick snap of the spindle orient would happen it would jump a tooth...
This is exactly was it was. The phases were reversed when wired up and the motor ran backwards.
Thanks for the help...
On a related note on this machine when we connect the air the spindle oil...
I am guessing no...its not powered up... the fan isnt running the green light isnt on.
I am not sure if i should be looking for anything particular. Where i am new to the machine and this is a...
the unit was never unhooked. We un hooked the coolant tank and pumps and the thru spindle coolant chiller when we moved the machine but other than that we moved it as a complete unit. When the...
We recently purshased and moved a 2001 Okuma MC-4020 with an OSP-U10m controler. After getting the machine back together and power to it we end up with a 2726 Spindle cooling unit alarm. We cant seem...