584,802 active members*
4,881 visitors online*
Register for free
Login

Search:

Type: Posts; User: gwiz

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    2,059

    Re: LagunMatic vmc 3516 no return home Dynapath 40

    If the axis is not referencing then try this. Jog the axis away from the reference switch. Reference that axis. Once the reference starts trip the reference switch by had (hold it on). With in...
  2. Re: Electrical "Short" sound during tool change and Excess Pressure behind toolholder

    I never had a Fadal but it sounds like a solenoid issue to me. Again, bad coil, loose, not shifting like it should.
  3. Re: 1996 4020ht - new to me, much maintenance required

    Sweet
  4. Replies
    1
    Views
    518

    Changing spindles from 7.5k to 10k?

    When replacing spindles has anyone ever replaced a 7.5k spindle with a 10k. Is it possible or is there more hardware other than the spindle cartridge?
  5. Replies
    2
    Views
    710

    Running a Fadal on a Phase Perfect?

    Anyone running a Fadal on a phase Perfect? Looking to run a 4020ht on a PT-10 or what use to be a PT-330.

    Any Issuers.
  6. Re: 1996 4020ht - new to me, much maintenance required

    How is it running?
  7. Re: Retrofitting a spindle chiller onto a Fadal VMC15

    Did you ever figure this out?
  8. Re: Kitamura with Fanuc OM control - 400 408 414 424 434 servo alarms

    Please keep us updated. That way we all learn along with you.
  9. Re: Kitamura with Fanuc OM control - 400 408 414 424 434 servo alarms

    Have you measured power at the that top plug? (Usually 220vac). If you have power there then it may be in the power supply. Try removing all the jumpers between it and the spindle drive to make...
  10. Re: Kitamura with Fanuc OM control - 400 408 414 424 434 servo alarms

    I may have missed something but here is what I know.

    If the drive package does not light up the main buss power contactor will never turn on. On your picture, top right you should see two red...
  11. Replies
    12
    Views
    2,404

    Re: Dynapath 50 software issue I think

    Great call CNGBRICK.
  12. Re: Kitamura MyCenter 1/485 - ground up rebuild and retrofit

    NIce. Glad to see it.
  13. Re: Kitamura MyCenter 1/485 - ground up rebuild and retrofit

    Any updates?
  14. Replies
    5
    Views
    1,459

    Re: Dead Dynapath System 10

    The last place I know to go to for a system control is partsandsmartsinc If Al is still taking calls he should have a couple of Ideas. I can't blame Dynapath on the lack of system support as it...
  15. Replies
    1
    Views
    1,359

    Re: Delta 20 programming error

    Just a simple note the the CR is carriage return and LF is line feed. These should not be characters that show on the screen but general formating. I think that is your problem. Not familiar with...
  16. Re: Dyna 50MU, access to the "monitor" functions or higher level settings?

    There is no load display for the axis on a dynapath. You can as mentioned look at the following error ie Lag display by going to your setup mode on cnc then selecting TM4 - Servo adj. Normal...
  17. Replies
    5
    Views
    1,459

    Re: Dead Dynapath System 10

    When I first started I did wire up a couple Dynapath system 20 but other than that I really had not contact with them. Now Deltas I can help you with. Give Dynapath a call, They may have some...
  18. Re: I never understood what Fanuc people meant by Fansuck until this 5700.

    I am sorry your having an issue with the Fanuc. I have a couple of comments. First, Doosan picks the CNC they offer on the machine including all the options and storage. The person who purchased...
  19. Replies
    6
    Views
    2,676

    Re: dynapath 20m " In Position " problem

    Cold Start

    Back up all your part programs, Macros, Tool tables, and offsets. (will be erased)

    Turn off CNC power. Pull the AUX card from the backplane for about 20 min.

    One of the few...
  20. Thread: Homemade 4th axis

    by gwiz
    Replies
    2
    Views
    1,492

    Re: Homemade 4th axis

    You could update it to a 4th axis The dynapath puts out a +- 10vdc command. And takes a 5vdc squarewave feedback. Dynapath is still around. And services controls. Another place is parts and smarts...
  21. Re: Compumill 4000, Dynapath Delta 20 no axis/spindle movement on new install

    Thanks for the update. The Delta 20 is a really good CNC. More reliable than there later models.
  22. Replies
    8
    Views
    3,184

    Re: What year is this Kit My center 1 Fanuc 0M

    Did you get them running. How is it going?
  23. Re: Compumill 4000, Dynapath Delta 20 no axis/spindle movement on new install

    Ok. I was going to start with the Override pot. (you should also check the switch on the back of the override pot. It can also go bad no mater where the dial is.)

    Next. The display highlight...
  24. Replies
    6
    Views
    2,676

    Re: dynapath 20m " In Position " problem

    Well from what you said a couple things come to mind. 1. loss of feed back for some reason. does the CNC see it drifting off position? If it does then I would say that something is causing some...
  25. Re: Any one successful with RGB to LDC monitor swap?

    You can not just add a board to the CNC. The Delta 10/20 were true CNC with all custom hardware. The 30?40/50/60 and Delta 2000 have a basis on PC hardware and can run VGA monitors without a real...
  26. Replies
    379
    Views
    69,182

    Re: Chinese XK7130 a complete experience Review!

    I spent last night reading this thread end to end. I hope you get the CNC worked out soon Would love to see the mill making chips.
  27. Replies
    1
    Views
    1,344

    Re: 099 TOOL NOT FOUND IN TABLE

    Not to be too obvious but did you check your tool table to see that you have a T1 in it. Not sure what type of machine you have this on but the Q table is used to hold tool numbers.
  28. Replies
    2
    Views
    1,667

    Re: Dynapath/Autocon 40

    I am guessing you have already found a solution.

    I have three.
    Contact Dynapath for a replacement, or
    Contact Parts and Smarts for a replacement, or
    Go to ebay and buy a used one.
  29. Replies
    54
    Views
    13,217

    Nice write up. a few notes. Be careful on...

    Nice write up. a few notes. Be careful on replacing the back plane motherboard with anything other than what Dynapath has deemed acceptable. It was a commercial/industrial unit and timing in the...
  30. Replies
    1
    Views
    1,102

    Not familiar with Tree in particular but it can...

    Not familiar with Tree in particular but it can be done by external switch or look on the status screen ( Fault/status key twice) there may be a soft key for block delete and optional stop. If not...
Results 1 to 30 of 52
Page 1 of 2 1 2