Thanks for replying, I forgot to update this thread.
I did solve this problem by tightening the gib just a hair, still had the same lost motion and backlash but previously was on the really...
Type: Posts; User: Djstorm100
Thanks for replying, I forgot to update this thread.
I did solve this problem by tightening the gib just a hair, still had the same lost motion and backlash but previously was on the really...
Pm me your email please. Love to have the chance to help you out.
pictures?
Short story is my table is trammed in very nicely at middle and left side of the table. However when the table is moved to the(right side of the table is close to the spindle) extreme left the table...
end up going with a Mistubshi ASX445 3" 4 insert. Buy 20 inserts and get the face mill for free. See some incredible finish with this tool/inserts.
- - - Updated - - -
end up going with a...
glad you got it worked out.
Makes me curious about mine as I've never check the spindle with the haimer turned. I to have my spindle marked in two locations so it's always inserted in the same...
Ray, SEHX is polished to a mirror finish on the insert it self. How does this insert perform? Mirror like finish on the part's surface?
Are they postive or negative rake? Been looking at the pros/cons of neg/postive
Think it was your thread that I read, regrading using only half the inserts.
so what face mill do you use?
When isn't power a limiting function of a Tormach?
Doesn't matter the cutting edges, limitation is HP. Don't have the power to drive 6 cutting edges .100 doc on a 3" facemill. One item I product I have to take .105 off one side and 0.050 on the...
if you have 6 insert but only use three it allows you to cut deeper/faster while still keep the tool balanced
oh yea...If it pulls out, it's the operators fault. But machine boges down way before it pulls out if properly tighten
While I like the surface finish of the super fly, it problem is from being such a big interrupter cutter and when having a step over there is a waviness (doesn't catch your nail). However as you...
Why is feed rate higher with external vs internal?
Hope this help some.
https://youtu.be/sDkAEhcRPrI
Thanks Mr Clarkson. I left enough wire and zip tied it around the wiring harness on top of the z motor, drilled a small hole in the axis cover toward the rear and ran it down.
I caved and...
How did you guys route the wiring, if you don't have the PDB?
I did a combination of shimming the corner to tram the X. For Y I placed small shims under the head where the heads bolts to the z axis carriage.
I was asking a genuine a question. What's with the butthurt?
What was the "other issue"
If your reach your hand on the ball screw (x and z at least) if you have oil, you are good? I typically will lower the head and squirt some oil on the z ball screw...
You are referring to the yoke that is bolted to the carriage for y travel? You can remove the way covers and get a socket wrench and allen head in there. If I'm miss understanding, I apologize...
Bottom of pocket to bottom of the part is 0.25
https://myhub.autodesk360.com/ue28fdd8d/g/shares/SH7f1edQT22b515c761e85670363bffacc7f
- - - Updated - - -
I agree, I think it's more of a...
Awesome, Thanks. If you choked up on the tooling more and was able to go down 1" what would your feeds/speeds be? My roughing goes around the part at 1" doc .04woc at 4500rpm. the interior...
Well I figured it out. Roughing left 0.005 on the floor and the wall. finished the wall but left 0.002 on the floor. Did the pocket and it came out smooth as a glass. Ran the part again but...
Thanks! I totally forgot about this video. I figured it out. Although I turned the finishing speeds way down. It came out perfect
Solution: Roughed out but left .005 radial and ...
Higher speed = RPM or IPM?
The floor is important because it's what I'm having issues with lol. how would you finish the bottom with out cutting in the wall? Would have to leave atleast 0.002...
Wouldn't that little ledge be noticeable? I'm more using it as practice for when I start taking on jobs.