Search:

I know this is probably a late answer but I am sure you will find this of use, very basic but I use it on my Lynx 220 and it works fine. you might have to play around with the speed/feeds for your...

This is usual on most lathes, look on your control panel for either a switch or maybe a softkey on the operator panel to switch to continuous cycle. In continuous cycle as with a bar feeder the...

Hi, the function of INP.C is to display the relative co-ordinates why would you want it to display The Machine co-ordinates?

Hi, from the Manual guide screen use the soft key to select "T-OFS" this should bring up the offset screen, using the arrow keys you should be able to scroll through all the options for offsets/wear...

Hi, looks like you are trying to connect through the printer port on you laptop. This is a parallel port, you need to connect to a serial port.

Had the same trouble with a Doosan 550, the problem began when a operator switched the machine off while the machine lock was switched on. Only way to switch it back off after powering up was to...

Hi, yes 5002 #6 set to 1 and the position should update as soon as you call the offset.

Hi,
on the Fanuc 32i there is a soft key option whilst in edit mode to "Change Editor" one has spaces the other does not. Use the left-right soft keys in edit mode and you should see the "Change...

Hi
What you need is a Universal Wi-Fi extender with a Ethernet port.

OOoops that should be G98 not G95...

F10 will move like a rapid if your are in G99 mode (feed per rev)
change to G95 (mm per min) now you can use F10.

Timer settings here goes, Press SYSTEM then PMC then PMCPRM and I hope you can know see the TIMER page, if not you will need to find how to display it. The first two TIMERS relate to the Lube Pump,...

Hi, have you looked in the electrical cabinet in the back of the M/C, if you are lucky the wiring/electrical manual could be there. The automatic oiler is normally controlled with the first three...

Hi, turn the power on while holding down the 6 and 7 keys. Hope this works.

Hi, you could try turn the power on while holding down the page up/down keys, or if you are using a 9” small unit turn the power on while holding down the cursor up and down keys instead of the page...

Hi. yes it certainly looks like an issue with the Motor, as for trying to repair or adjust it I would leave it to the "experts" and send it for repair. Here in the UK its easy to get a Fanuc Motor...

At what point does the Alarm occur?
It could be something as simple as bad contacts on a relay depending at what point the the machine Alarms out.

Have a look inside the control/electrical cabinet of the machine and If your lucky you will find a book/listing containing the information you require, if not somewhere on the machine you will find a...

Hi, yes it is a parameter issue. A good place to start would be to look in your parameter manual for parameter 5002. Various settings but do not alter anything unless you are sure what you doing.

Could you post a snapshot of your screen display whilst in Manual Guide mode.

Hi, are you in edit mode and use the left/right softkeys to scroll through the different softkeys. there is parameter values to change these keys but they should be set by default.

[QUOTE=econcepts;2023146]There are complex instructions on how to configure the fanuc controller and part of that is a specific ip address that looks suspiciously like an autoconfiguration address...

Just connect the pump to any Ethernet port on the same network that your machine is on, It will work, trust me..

I have noticed your are using manual guide to simulate the tool path. Have you checked the tool type description in the manual guide offset page? there are more settings for the tool description in...

Try This
the chuck must be clamped or it will never work
G97M5
M19
G97S0M3
G98
G1Z50.F200.

This is a very basic easy to follow way of how I would do it. Dont forget to end your main prog with M99.
%
O0012(SUB FOR 9)
N1G10P0Z385.(Z position FOR FIRST PART)
M98P11 (P11 IS YOUR MAIN...

Plenty off stuff on you tube, try this link

https://www.youtube.com/watch?v=ZYSu7_WZxg0

The filter is located inside the hydraulic tank,

Hi
Does anyone know the parameters/settings to limit the output of X,Z,F information when converting from EZ/ Manual guide format to NC code,
Some of our controls are outputting X,Z.F values on all...

Hi
Does anyone know the parameters/settings to limit the output of X,Z,F information when converting from Manual guide format to NC code,
Some of our controls are outputting X,Z.F values on all...