Search:

hello
we have built a new sensor ....
Sensor-fuer-MAHO-Doppelgreifer
best regards
mtronik

Hello,

the page has changed...

Hello

I guess that your power supply is on the right side of your controller.
With these power supplies you don’t have the possibility to check the voltage.
Unless you take the controller...

Hello
Unfortunately I don’t have the required circuit plan either but on the 300C i get the error message 1Q1, motor protection main motor fan.. you could have a look at that..

Regards
Mtronik

Hello
You can find the battery in the power supply underneath the controller (aluminium-box at the bottom right)
The power supply is adjusted with 2 Imbus screws. Unscrew the screws and then pull...

Hello

what controller does the machine has 432-9 or 432-10 ?

Regards
Mtronik

Hello

the battery is hidden in the power supply unit.
Regards
Mtroni

Then we found the error already:
The three-phase bridge rectifier 5V1 is defect.
Hence the “wrong error” I62, the power supply for the end switch breaks down and therefore error I62.
Have you got...

Hello

I just had a look at the You already have the circuit diagram of a MH300C. The warning device is really coupled to the 24Vsupply with error 37.
Have you got a measuring device? Then you...

Hello
What controller do you have exactly? 432-10 or -9 ?
Do you know where you can see the I/O Status?
What gearbox have you got? 2 or 18 steps?

Regards Mtronik

Hello
Error 37 is the follow-up error of error I62.
You should unscrew the lateral top of the spindle stock and check the position of the switch cams.
Are all the switches on the cams? Or maybe...

Hello

To 90% the screen
@ cgTNC

All Phillips controller apart from the Mill-plus have a CGA special timing.

Regards
mtronik

I am urgently searching for the machine parameter for a NEF500 plus.
After a battery defect the parameters are gone, no data backup and DMG doesn’t know anything.

Regards mtronik

Hello
the #05 is the emergency stop on the machine as a consequence of the error M01.
Error M01 is a Checksum-error in the constant memory. The reason could be:
Battery empty, machine parameter...

Hello
The note FUE is the field current and the note PUE phase monitoring..
I guess that one of the ultra quick fuses at the top left in the switch cabinet is damaged.
You can only measure it with...

Hello
The game that you determined is not relevant for the accuracy, because the measurement system is directly positioned on the axis.
However the spindle game can cause problems during the...

Hello
It could be that one or several axes are drifting away- that means that the axes are not in the “IN- POS” window anymore.

If your set parameter 81 to 1, then you can read off the drift. If...

Hello

If the machine has direct current motors, then check the motor carbon brushes.
If the AX engines are mounted, then I guess the AC controller is defect.


Regards
Mtronik

Yes, rewinding is almost always possible... is also a time and money question.
Have you got a type description from the transformer or a picture?
I have several transformers on stock.

Regards...

You have to be careful that the feed control ( 180V) gets its synchronisation also over the 180V.
Otherwise it should work.

Regards
mtronik

Hello
The signals and wire colors are described in the circuit diagram of the machine.
Good Luck!!

Regards mtronik

Hello
M03 Checksum error background memory machine constants
M60 Checksum error work piece program memory

Regards

mtronik

Hello

What kind of problem do you have?

Regards, mtronik

Hello

I suppose 1000C is an old machine. In that case you'll find the accumulator in the power pack of the controller.
If the controller is in a command station, screw the control panel down (4...

That’s my address:

Kuhn Industrietechnik
Reichau 32
87737 Boos

Regards, mtronik

That’s me again

There’re parameters of 400E / software 6410/404 in the attachment.

But use them carefully because I don’t know the options.

So it’s without guarantee.

Regards, mtronik

Hello

You may send the perforated tape to me. I’ll read it out and send a text file for transfer…

Greetings
mtronik

Hello

Berus = proximity switch

Unfortunately I don’t have a connection diagram of MH600 with controller 532.
You should check whether the signal comes from the proximity switch in the...

Hello

Check the berus of the tool clamp. It has to inform if the clamp is open.

Greetings mtronik

Hello
The drift in one of your axis is probably too high. Set the parameter 81 to 1. Then you can read off the current drift on the display. Is it higher than 10 increments, then you can’t process...