Search:

Yeah it turned out to be my computer once input a smooth stepper in it took care of all my issues


Sent from my iPhone using Tapatalk

I picked up a ess from warp 9 and it solved all my issues. I wasn't running my g0704 mill at the same speeds as the router table so I never had any issues. The one thing I'm still trying to get...

Hmm what do you mean? How would I find that setting.


Sent from my iPhone using Tapatalk

I'm guessing so.. It's a cnc router parts kit and when I spoke with them they are saying they can run a lot faster but he also did recommended a smooth stepper. I don't hear the axis binding up and...

So I'm pretty sure I figured it out. Mach3 is running at 45khz kernel speed and my z axis takes just under 2040 steps to move 1" if you divide those you come up with 22.059 mm/sec if you divide that...

So I'm thinking the best way to do it is going to be with an arduino board with a servo motor driving the airbrush needle off an input from mach 3 though the c10 breakout board. I started designing a...

So im starting to get really frustrated with this thing... I just ran the sign again today and im still having issues... Ive attached a picture of what its been doing. I have already ran a pre done...

Got ya. I'm also going to remove my anti virus because it popped up a screen saying it's out of date...


Sent from my iPhone using Tapatalk

sweet!!! I was wondering why i could run smaller 3d jobs like a breeze. I shut off the screen saver and checked power saving settings. The power settings were already turned off. is there an easy way...

So I tried running this big job again today but before I ran it I made sure all my wires were shielded and I also separated the router cable vs the control cables in the wire track. It ran great for...

I wasn't originally running sherline mode I ran the job with it on to see if it made a difference and it seemed to run better without it. The motor I wired in bipolar parallel so I could get my...

i missed your question about the voltage sorry.. the powersupply is 47.9v and the drives are rated from 20 -80 50 is typical it says and for motors they are NEMA34 Stepper Motor – 906 oz in 6.1A...

The one thing i want to change is the wiring on the z axis. all my other motors I am using shielded 18 awg wire and i ran out for the z axis so i ran 4 separate wires that are not shielded. I also...

Hey gerry thank you for the help. I am running a cnc routerparts kit. The z axis assembly came as one piece and it is ball screw driven so im not sure what the pitch is since i didnt order it. Yes...

Hey guys I'm starting to get frustrated with this build and looking for more help. I'm using kl-8060 drives outputting 5.43 amps. The motors are nema 34s and rated for 6 amps. My drives are running...

Any other advise be vides acceleration and drives over heating?


Sent from my iPhone using Tapatalk

I am using KL-8060 drives. I read through the literature on it and it says my pulse and direction length needs to be about 1.2 for reliable control so I'm using 2 usec


Sent from my iPhone using...

Hey guys I thought I'd start a thread on incorporating a airbrush on a cnc router table. I have been doing a lot of research on adapting one to a router table and haven't found much support. I've...

I'm done running it tonight but I did adjust my acceleration to 30 on all the axis's. Maybe I should take a box fan and put it In front of the drivers tomorrow and run it to see if that makes a...

Now that you say that my girlfriend said to me yesterday that they were warm through her jeans. I've been done running it for about 45 min and they are definitely warm to the touch. I do not have a...

I can put my hand on the router and drive the motor up and pull down slightly and it doesn't miss pulses it pulls my hand up and down no problem


Sent from my iPhone using Tapatalk

I can try to decrease my acceleration but if I was losing steps shouldn't I see it in more then one spot?


Sent from my iPhone using Tapatalk

My acceleration rate is set to 40 acceleration and 150 velocity on my z axis x is 1000 v and 40 a and y is the same as x. Basically I'll run my roughing file and it runs perfect. Next I swap to my 3d...

Hey guys quick question when I run a 3d rough and finish in vectric aspire on my router table my sign gets about half way done and my z axis changes... I'm running 50ipm with a 30 ipm plunge. Do...

It was working but not well. I pulled up my spec sheet on the drives and it said that I should be over 1.2. I changed it to 2&2 and ran a 3d part last night and it came out well. I think what was...

Just curious if the pulse/direction duration was to long how would that affect the cnc? Also if it's to short?


Sent from my iPhone using Tapatalk

I changed it to 0 usec on both settings and it's running good now thanks guys!


Sent from my iPhone using Tapatalk

I double checked it and I was already at 5 usec. I'm not however 1/2 sherline. On my mill I was running 0 and 0 on the settings in motor tuning. I changed the settings and ran a small 12x18 piece...

Hmm I have to check that. Is there a certain way to calculate my pulse length or is that something that is in the drive specs?


Sent from my iPhone using Tapatalk

I'm going to face off the spoil board again just to test it again and see if I can see what's causing it... I'd hate to be working on a big sign and have it put divots into the face of it so I want...