Hello,
We are making stamps and cutting dies. We sometimes having problem to fit them together. We cut punch in one pass with E2 (Rough is 2.8 RA) cutting technology. My question is how other people...
Type: Posts; User: xal3r
Hello,
We are making stamps and cutting dies. We sometimes having problem to fit them together. We cut punch in one pass with E2 (Rough is 2.8 RA) cutting technology. My question is how other people...
Please send me to [email protected] thank you :)
Hello, we have the problem, we want to reinstall software using 5inch floppy drive. We got the external floppy drive, but we don't have the cable for it so we are looking for electrical diagram fro...
Hello,
we have cloned the old 16 inch floppy disk with parameters in it from ocuma lb 15 osp 5000-LG, we can't open floppy with windows, because it has different partition in it. So the question...
The error with the new cpr board and old bubble memory board : https://www.cnczone.com/forums/attachment.php?attachmentid=416814&stc=1
The error with new CPR board and the new bubble memory...
Maybe there is a way to show example of that cable? i will say to our service guy to check that cable.
After we buyed the used cpr board from ebay it was not exactly the same but very similar because its hard to find exactly the same, and now when we replaced that board that error was solved, but...
We had the CRP board problem before, when the machine was starting the machine gives us LIC C1 plane test NG addr error, and the machine didin't start up. So we bayed the CRP board but we are not...
Thank you for your help i appreciate that, we would like to know more about SRAM BOARD, maybe you can post a link for that board from ebay or just picture. The second question is the connections is...
Hello, we are struggling now witch okuma lb 15 osp 5000l-g machine, we have bubble memory error and we think that we need to reload software and parameters, we have 8 inch floppy disk with...
Hello, we are looking for Okuma LB15 OSP 5000, software and parameters disks because we did not get them when we bayed machine. I know that parameters may not be the same, but maybe will be the...
We found a board replaced it yesterday it was working all day but this mornig when we start the machine again we got an error any suggestions?...
https://www.cnczone.com/forums/attachment.php?attachmentid=411000&stc=1 EUA-IC0502 Contol Board XPS-451
we are looking for this board for now https://www.cnczone.com/forums/attachment.php?attachmentid=410996&stc=1https://www.cnczone.com/forums/attachment.php?attachmentid=410998&stc=1 if you have...
Hello,
we are looking for used but working cpr board, like we add it on photos.
Hello,
All started yesterday, when i turned on the machine in the morning. I started the program, and the work speed was very low not normal on x and z axes. I mean the drilling speed was decreased...
Hello, we have Robofill 440 wire cutting machine, and we got an issue when we are set machine cut at night time with a long cutting time. After 4 hours in cutting progress the machine goes to energy...
Hello,
I have a question maybe someone will know how to switch off auto wire when the wire breaks, because our machine auto wire does not work properly and we want to put wire in manually. Im...
Problem solved ! don't know how to close post
Hello,
We have an issue, we have charmilles robofil 440 sl edm wire machine and now we got an issue, when the WINDOWS NT starts its get stuck on blue screen i add the photo in files. We took out...
Hello,
We have Charmilles Robofill 440 machine, now we got and issue that Y - axis is over travel and we can't clear this error. What we try to do is first of all to go revers in hand mode to Y +,...
Hello,
we are trying to set up ''Gotek'' usb floppy emulator, but after we plug it in , when machine boots up we get the problem ''ERROR 02B2 Incorrect Drive A type-run SETUP''
44-TU100 GOTEK...
Hello, im using Charmiless robofil 440sl machine, the problem is now that program graphic map is not in the same position as program. When i load the program as i shown below the program goes to...
Hello to everyone,
We have charmiles robofil 440 machine, and when we set the zero point on the part and start the program everything works just fine, but when we cancel the program and start it...
Hello, we have just bought used Charmiles robofil 440 sl edm machine , we have older machines like robofil 290 and 330f, but now we got a bit newer machine. The problem is that the main langue is a...
Hello,
We got an issue. Our machine efficiency is decreased. Machine model is Robofill 330F Our cutting speed went down now. We are thinking that the problem could be the generator voltage...
Hello, we got an error on our ocuma lb 15 lathe machine. The issue is : Fault 247 Touch setter limit 1 error. We find out that the problem is with sensors in the touch setter arm. We tried to...
Thanks for advice guys :) but can someone just give me example of m3/ m4 code. For example i need to tap M6 in a blind hole let it be z - 10 deep. I will use floating holder.
I am just starter...
Maybe anyone knows how to tap with this machine? I wrote simple program with Mastercam , but the pots processor is for Fanuc Ocuma controller and our is OSP-5000. But i usually write programs like...
Hello, i am looking for Older version of Chiron machine (myone is Chiron FZ 33) deep drilling cycle program ( peck drill) program code. I want to compare with my one because my peck drill does'nt...