I'm making a spindle mount for my cnc mill to utilize and nsk spindle. i need to know just how much clearance is necessary for this to work properly. i really don't want to cut too much out of the...
Type: Posts; User: m8kingit
I'm making a spindle mount for my cnc mill to utilize and nsk spindle. i need to know just how much clearance is necessary for this to work properly. i really don't want to cut too much out of the...
Does any know where i can get some specs on a te-05 pendant? I'm wanting to know if it will work with mach3. and what i will need to make it work. There are no specs on it, however, it has 24 pins...
i remeber ahile back someone was telling me that they made a homemade pendant froman old game controller or joy stick.
I'd be interesting in hearing about it , if any has any knowledge of these....
Nothing has changed. The wires that were disconnected were color coded, so there is no way they are reconnected incorrectly. My guess is that if it was a connection , there would have to be two...
I recently disassemebeled my machine to move it. i disxconnected the axis by removing the splices between the controller and the mill. However now that i have reconnected everyhting, my x axis will...
Does any know how to remove the spindle bearing in a chinese mill? I recently purchased a mill that was supposedly new, however it had sat on a loading dock for a while and was claimed as lost...
Thanks Mariss, I'll take your advise. I guess in my situtation was not knowing my motors rated cureent. i have a cnc masters mill, that i'm restructuring the controller to enable the use of mach3 and...
Mariss, Do other drive manufacturers make their motors different.
People like intelligent motion and a few others instruct you to set the current limit to 1.4 x the actual current.
I beleive...
I do have a question. Why do other manufacturers have you determine your current resistor setting by multiplying the actaul current by 1.4? does this go to say that if you used the actual current...
i have a hypothetical question in referrence to geckos and other quality drives. I've noticed that gecko has you set the current to the actaul current rating of the motors, however, other...
I've decided to use im804 drives, i'm just need ing some help deter ining the best settings. I recently had gecko201's , whichwere 10 steps, but these new drive off different resolutio settings and...
Does anyone know anything about these drives or where i can obtain the specs or pdf files? All help will be greatly appreciated.
thank you
Mark
Thanks, I was following your steps, with the exception of the reboot, I wasn't aware of that
Mark
I'm trying to use the auto settting to determine the correct amount of steps on each axis. However, each time I'm off by a few thousandths and try to get closer, mach three comes up with some out of...
I've added a c-11g board to my cnc master's mill and now I'm having a hard time configuring it. I had it configured corrctly once, then i proceeded to add the spindle relays and try to set the...
Mike, I can't seem to get any voltage from my analog. I've gone back and read what i can on the c-11g board. i went into the spindle tuning and set the velocity to max, along with the acceleration,...
Mike, Ironic that Art just emailed me back and said what he had told me about pin 15 step was a typo it is pin 14 step and 0 dir.
i should be running today, I'lll let you know. You've been a great...
Mike, you seem to have given me the missing pieces that weren't explained anywhere . i was lost about the pins and outputs in that ccw and cw window. The rest I pretty much figured out, with the...
I'm in the final stage of the redo of my cnc master's mishap controller.
I'm installing a c-11g board , however i can't find enough documenttaion to finish hooking up this vfd I have a shematic...
So I'm just crossing the cap terminals with the resistor or bulb . do i necessarily need to do this to all of them, i used 30,000 mfd, but i used 6 x7500?
Al, the gentleman that had me wire it...
ok al, so I should leave the red and the orange wires on the bridge, then to just connect the two side of the bridge pos and neg from the bridge to the caps. what is the safest way to discharge...
Al I have the red and the orange attached to the bridge , then i used the postive side and the blue wire from the center tap, and this 76v dc is what I'm getting.
looking at the schematic i have...
These are cnc masters motors, probably kelling 1200 oz/in 5 amps. but there is no more information to be had. Maybe I'd better'd back off the voltage. This is a cnc masters machine that i revamped...
I see what i did i connected the red and the orange to the bridge and the outer wire as my ground, not thinking , lol.
Al, I did connect the primary paralell the 2 120's and the grounds.
Will...
Yeah I know that's what it sounds like, lol i had someone from here tell me to wire it that way. I'm using gecko 201's, will this hurt anything .
I was under the understanding that the terminal...
According to this schematic, I should have @40vdc ,but i'm measuring 76v dc at the drives . Can anyone explain? I've attached a schematic of the torroid i used.
This had 4 taps 4 x27vac, but...
I've installed the c-11g breakout board on my cnc masters , so that i could use mach3, and still have my variable speed spindle.
I've worked thru the resyt, now i'm at the point of wiring the vfd,...
There was another three wire method shown in the attached pdf, but for some reason it wouldn't allow me to attach it. I tried resizing, but still to no ado. See what you think, let me know if you can...
Henrik, If i showed the pdf of my vfd, do you think you could help in getting it wired to my c-11g. They give a schematic, but a few things aren't real clearto me, i'm not and electronics person....
I'll have to look at the manual on mine and see if this is possible for me to do. i like that pretty neat