Search:

Hello, I have a similar problem, I do not know how to increase the light intensity, it is very dim and some vertical lines are slightly brighter..
Any help would be welcome :)

Yes, I'm almost a year late,
but we have everything for this machine
479256

Hello
the problem is with HEAD 2,
it moves if we press 2.O.T. release and then the X and Z axes can be moved using the HND wheel.
What can be the meaning of 2.O.T. release on this machine ... ??...

We use and recommend from ebay
DNC ADVANCE. RS 232 To USB Reader. Drip Feeder DNC
that costs with sending $ 200

The machine stood for 5 years .. it lost programs and parameters!
I have a parameter book, except for the OP parameters!
the machine is from 1993, it's a shame for such a beauty not to breathe...

I have the parameters of MORI SEIKI MV JUNIOR, serial number 2610 with Fanuc 10 ..
where should i send you?

Yesterday I made a backup of the parameters and PMC data, from SL-25 ser no 855/1988, SYSTEM: F10T9B 1260B.
If anyone needs this, I'll be happy to send it to you.
btw, the moderator could create a...

Can someone help with instructions, how to setup Fuji Frenic 5000W Drive
thanks
dj

Hi, this should be a problem with the spindle encoder, it's possible to break the belt between the encoder and the spindle !

Does anyone know how to power board A20B-1003-0010, ..?
I see it is not 2xAC19 .. but I do not know how much and where it is.
regards
djordje
403750

Hello!
Are there any changes if you command 2500 rpm?

Hello everyone!
Trying to fix a few servo units.
Need help with conditions necessary to dc servo SOCADIN SA-3 could run on the table.?
It would help the schematic from some machine with this, and...

Hello, I have scanned the complete manual for this machine .. Give mail or write to the PM.
greeting
dj

Hello everyone
OKUMA OSP 3000L
After turning the machine bright RUN about 1 sec and then a change in M-PAL.
Do not react any button.
Any advice is welcome!
greeting Djordje

Hello !
I have a similar,
Machinecenter Leadwell FMC 0
send an image to see what is the problem ??

I hope it will help

Hi, I have something scanned, send PM

is it board NSV54 ?
did you check 24V supply

Yes, you have problem with driver components for blown transistor.
Manifestation is typical when one of six transistor not working.

Hello!
How can to change angle for chamfering in thread cutting,
on Lathe with Mazatrol CAM T2?

regards from Serbia
djole

Display: A.
Description: MDI Connection Failure.
Repair: Check fiber optic between cable connection control and MDI/CRT unit.

We have several times this alarm when have problem with power...

maybe this can helps

Hi Harmeet,
we solved similar problem changing bus drivers in ROM cassette, like 74ls373 or ls244.
good luck

hello brother , try to change parameter N12 from C-1 to C1 or reverse
regards, good luck

Bok stari,
Hi, it's better if you write in English here, out of respect for other visitors Forum.
I would be glad to contact me on PM djordje at datatehnik dot com
regards

Hello Arjuna
You can have problem with GRAETZ and capacitor on main power for servo motors, or transistors on some servo unit.
first check for short connections at diodes and capacitor, after that,...

huh you can write:
G0X90.0;
G01Z0.0F.2;
X100.0Z-5.0;

it will make 45 degrees

Laka thank You, I will try it asap
regards djordje

This machine is new for us.
The machine is homeing first time, after grip on the HOME button, she start to moves, first Z ,go to mach 0.0 ,and dislocate around 1mm after that moves Y by same routine...

Thank you Prabhat !
Machine normally goes in JOG mode, all тхрее axis go to the reference, after which it is removed from the home position and report alarm ...
b.t.w. we have not manual from MTB...