512,969 active members
2,547 visitors online
Register for free
Login

Search:

Type: Posts; User: MarkT

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    590

    Re: Fanuc OM z axis crash

    When some Fanucs crash, there is a setting that must be enabled in order to allow you to move the machine. The concept was after a crash and inevitable motor slippage, it was an additional safety you...
  2. Replies
    1
    Views
    13

    Re: Biesse Rover A Surface touch off

    Typically you do not touch off to the table on a Biesse. You measure the tool length after the tool is mounted. With HSK spindles it is the measurement from the backside of the toolholder flange to...
  3. Replies
    1
    Views
    21

    Re: Biesse Cnc non Tlp problem

    You need to adjust the sensor mounted externally on the piston. If the LED on the sensor will not light up, you probably need to replace the sensor or wire. In the rare case the piston does not move...
  4. Replies
    24
    Views
    69

    Re: Uploading to Biesse

    Chev, good AND YOU?????text me sometime
  5. Re: Biesse Rover 45 - "PLC9001 - Thermal relays KO (in 0)" error ?

    There is a break in the 24vDC emergency circuit ( estop, breaker, thermal overload tripped, etc.), yes the thermal relays are standard overload protection however some may have auxillary contactors...
  6. Replies
    1
    Views
    29

    Re: software NC500 leave a log file?

    Yes, but you would have to activate it prior to processing in the Statistics portion of the control
  7. Replies
    1
    Views
    271

    Re: Bisees Rover 23 with NC500 Controller

    You are going to have lots of issues. First the NC500 was considered a panel processing control, so there are limitations on lines of code per program. This can be a drawback with engraving programs...
  8. Replies
    24
    Views
    69

    Re: Uploading to Biesse

    ISO is the "loose" term here, these machines will not run standard eia/iso/"fanuc" code. They will however run code from previous generations of their control software, If your CAM provider has...
  9. Replies
    2
    Views
    50

    Re: Biesse Edge NC 410 cutting issues

    Mechanical checks _ Z axis compensation cylinder, Z axis motor, Coupling of Zaxis motor to ball screw, air pressure during operation
    You say this happens with an Alphacam generated program? if you...
  10. Replies
    26
    Views
    50

    Re: Biesse Rover 30 L2

    OK, first if your machine is a Rover 30 it may not have BiesseWorks, it probably has the preceding software package NC1000 which was much more popular on those machines. When you received the...
  11. Replies
    1
    Views
    42

    Re: Biesse rover 23: Z axis unaccurate

    Check that the Z axis Compensation Cylinder is set to the correct setting, also monitor its pneumatic gage while operating the machine.
  12. Replies
    3
    Views
    39

    Re: Biesse tool changer problem!

    There are also internal sensors inside the HSD spindle that can sometimes need to be adjusted. There should be an address at the end of your error that will tell you which input the machine is not...
  13. Replies
    33
    Views
    273

    Re: Biesse Rover 321R CNI Compact XNC

    If the control has the network card, you can network it but it would only be to a much older system (think Windows 98)
    The reason most people program the manner which you stated is, for panel...
  14. Replies
    1
    Views
    27

    Give Richard a call at 1.215.310.8464 -former...

    Give Richard a call at 1.215.310.8464 -former Komo tech now an independent.
    Tell him Mark reffered him.
    Most gantry routers are rigid enough to cut aluminum but no where near as rigid as a vmc....
  15. Replies
    6
    Views
    43

    I was a Biesse tech and have worked on them for...

    I was a Biesse tech and have worked on them for over 12 years...20+ cnc experience, I dont deal in "theory" :)
    You dont start with A=0, you start with A=A. I said that once started the drawback to...
  16. Replies
    6
    Views
    43

    Ummm..Sorta....my technique does not require the...

    Ummm..Sorta....my technique does not require the program to be run off the worklist.
    You need to program the counter logic in also..counter equals 1 jmp to XX , counter equals 2 jmp to YY, counter...
  17. Replies
    1
    Views
    12

    What is the control on this machine? Typically on...

    What is the control on this machine? Typically on the Biesse's I have networked in the past, the network connection only provided you the ability to move programs created on an offline pc to the...
  18. Replies
    6
    Views
    43

    I have used jumps directly related to PLC...

    I have used jumps directly related to PLC conditions on the XNC / NC1000 Biesse controls, but have never had a customer ask if it can be done with the NC400/NC410/NC500 control, so I am not sure....
  19. Replies
    2
    Views
    38

    If this is a three phase machine, switch two of...

    If this is a three phase machine, switch two of three incoming voltage lines. It sounds like you are phased backwards.

    Mark T.
    CNC Custom Services - CNC Service, CNC Support, CNC Training for the...
  20. Replies
    7
    Views
    940

    I should probaly clarify, when programming on the...

    I should probaly clarify, when programming on the conversational side then if you elect to convert it to G code, the on board post selected different canned cycles for some features as oppossed to...
  21. Thread: American made

    by MarkT
    Replies
    10
    Views
    23

    Haas, who is a more prevalent cnc metal machine...

    Haas, who is a more prevalent cnc metal machine manufacturer uses HSD on their small sheet router, other american manufacturers that use(d) HSD spindles (owned by Biesse, Pesaro Italy) that I know of...
  22. Replies
    10
    Views
    22

    Will not run with the active error..from the...

    Will not run with the active error..from the homing screen

    reset,pause,clear,pause,soft key for global home
  23. Replies
    10
    Views
    22

    Contact Biesse with your serial number and see if...

    Contact Biesse with your serial number and see if you can obtain the original machine data, constants and PLC. You are going to need to know that is good if all electrical has checked out.

    Mark T.
  24. Replies
    10
    Views
    22

    P.S. - I would LOVE some service work in New...

    P.S. - I would LOVE some service work in New Zealand LOLOL
  25. Replies
    10
    Views
    22

    I think you need to switch the values for the...

    I think you need to switch the values for the right head to a value greater than the distance from the home position to the switch if the left head was at home. I think that is where you start. Need...
Results 1 to 25 of 159
Page 1 of 7 1 2 3 4