Your memory space is full
Take out some old programs make room .
If you trying to download a 1 meg program and your machine only holds 1/2 a meg.
you have to break you program in half ,run the...
Type: Posts; User: timlkallam
Your memory space is full
Take out some old programs make room .
If you trying to download a 1 meg program and your machine only holds 1/2 a meg.
you have to break you program in half ,run the...
use a sub pogram maybe
I have a clausing with a 21 t control take a picture of the keypad to see if it is the same
as mine.
In my opinion Service center brand aluminum is the worst I have lot of bars oversize I can't use.
The chips don't break very well to gummy ,I avoid it like the plague.
I have always used Alcoa...
I have a Sharp 2412 mill my spindle was getting to the 100db range changed the timing belt now
its back down to 70db . The belt looked fine also check that the belt is not riding to hard on the...
There is usually a switch behind the turret .
If you crash the turret will move and close the switch.
Nothing will work until you straighten the turret.
The math is simple, if 4ms (4 hundredths of a second)
Isn't 4ms = 4 thousandths of a second.
I have a Sharp 2412 2005 model this is how I would write it.
T5 M6 (Tap10-32-HSS-TiCN)
G0 G90 X3.016 Y-0.8629
G43 H5 Z.2 M8
M29S640
G84 Z-.42 F20.
G80
G0 Z3M9
G53 Y0
M30
Some times material has stress in it.
You may need to rough it and leave everything .01 under size
and let the part sit overnight and then do the finishing.
I think you problem is with the slot...
Dom tube doesn't machine well at all could you use a different material.
I have the same control but my machine is storm 80
I use mastercam also it will put out a lot of unwanted code unless you can change the post
processor .I never tried to change ours. To complicated...
I run a lathe with a 21t control also
G97 S1000 M3 TURNS SPINDLE ON turns at 1000rpm
G97 S1000 M13 TURNS SPINDLE ON WITH COOLANT
For constant surface speed you use G92 as a speed limit or...
I have a 1998 clausing storm it has a number 4 taper . Not sure for the Tornado.
The threads your referring to.There is a nut with a hole in it.
you screw it on before you put your center in and...
I have been a cnc machinist 20 years , I have my own shop and make
a good living.
Not near the ability you have just lathes and mill no 4 and 5 axis.
I can honestly say i have never written a...
My girlfriend had the exact symptom's you have .
Tried antibiotics nothing worked coughed day and night no relief . Doc took cat scan had a spot in the lung
then a biopsy of the lung
and it was...
G92 is used with constant suface speed (G96 )as a max speed limit. Or as a work shift .
Lets say you you have a 6 inch dia. part to face and you want to use constant surface speed( CCS) of say...
Oo123(main program) EXAMPLE
T0101
S2000M3
GOX2
M99
Put M99 at end of the main program instead of M30
Write separate up program this is called the sub program
O0345(sub program)
PPC metals phone 704-283-9122 they can do everything you asked in your post .
Have you checked the H limit on the tap
If youre in g95 mode your code is correct
If in g94 the feed should be F20
Max I don't think you understand . You didn't lose your parameters you lost the absolute encoders position. First buy a new battery when you open the machine cabinet its about chest high goggle the...
What has most likely happened is you axis battery's died they only last 2 years. They keep power to the encoders when the machine is off so it won't lose it position.
The parameter battery's last...
Hello James , Brazing the shank on and expecting it to run true never did work.
So now we braze on the shank and then machine it holding the shank
in a collet.
I have found checking for runout...
SHARP 2412 TOOL CHANGE MACROS
%
O9001
#3003=1
#3004=1
IF[#100EQ#4120]GOTO99
IF[#4120EQ0]GOTO99
IF[#1011EQ1]GOTO99
G91G28Z0.
Put an indicator in the chuck tram the inside of the drill holder move x using the mpg until it is centered and that will be X0 for your drill.
Drills and taps are set at x0 Tram your drill holder get it exatly centered push measure key type in x0 then press measure key .
example to drill a 1 inch hole 2 inchs deep
T0101(1 INCH DRILL)...
Tool seting fanuc 21
To set work shift
move the tool to to your zero point( touch off tool 1 in program)
press off set key
press right arrow soft key TWICE( the soft keys are under the screen...
I have a sharp 2412 it doesn't uses much air you should be fine .
12l14 need about a .01 to.02 inch depth of cut to get a good finish.A light cut seems to tear the materal insted of cutting it.
Go into cimco setup and put 50-100 mili seconds pause between blocks . Your computer is sending code to the machine faster than it can handle.
Hello Travis , For setting the X and Y axis move the table where you want X0 and Y0 to be .
Go to the offset screen highlight X under G54 key in X0 and press the measure key ,its the soft key...