512,420 active members
4,841 visitors online
Register for free
Login

Search:

Type: Posts; User: fomaz

Page 1 of 14 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    163

    Re: What insert is this?

    No one?
  2. Replies
    2
    Views
    163

    What insert is this?

    I have a udrill that I do not know its brand. It came with a machine that I have bought used, and the udrill works fine.
    I want to get inserts for it, but it is being a hard task in finding its...
  3. Replies
    8
    Views
    1,101

    Re: IPM servo drive problem

    No. In my case they were "surface mount resistors", very small, low power. Those that you are showing are probably for the power circuit.
    I believe in my case they were on the control/signal part of...
  4. Replies
    8
    Views
    1,101

    Re: IPM servo drive problem

    In my case the error was persistent. The resistor was one of those that are rectangular - I do not know the name of that type. I have replace it with a standard one.
  5. Replies
    8
    Views
    1,101

    Re: IPM servo drive problem

    Hello,
    In my case it was just a simple resistor that was broken. Since the amplifier served two axis X and Y, I was able to compare both circuits until I found a difference. Looking more carefully I...
  6. Re: VFS5 Spindle drive problems cincinnati milacron

    :banana:

    Now is working. Thank you Mike. Good health.
  7. Re: VFS5 Spindle drive problems cincinnati milacron

    Ok, drive is working properly but I still have an issue that I cannot pass though.
    In defining the spindle speed drive range, we are able to set the gear ratio - Input gear teeth in the menu below....
  8. Re: VFS5 Spindle drive problems cincinnati milacron

    I would say wine is better than beer here. We are on a very touristic area. Maybe someday you pass by....
  9. Re: VFS5 Spindle drive problems cincinnati milacron

    Mike you saved my day. Motor had 2 leads swapped!
    The amps were about spikes of 100A, then we changed the motors leads .... and celebrate!
  10. VFS5 Spindle drive problems cincinnati milacron

    Hello to the forum.
    I bought a used/old stock Falcon lathe that came with a VFS5 drive for the spindle motor. Model is 275-00

    This drive is in the same power bus as the servo drives that are...
  11. Replies
    1
    Views
    855

    Re: Kollmorgen Motionlink Software

    Hello,

    Were you able to get it? I also need the software to connect also to a VFS5 drive.
    Thank you
  12. Looking for a quality servo motor/drive supplier

    Hello,

    I am working on a new machine where I would like to buy AC servo motors with drives (packages) on the 1 - 1.5Kw range. On the total would be 30 units where 3 units are used for each...
  13. Replies
    2
    Views
    490

    Re: Headstock lathe lubrication recommendation

    Sorry. It is a Falcon 200
  14. Replies
    2
    Views
    490

    Headstock lathe lubrication recommendation

    Hello,

    I have start hearing a small noise in my headstock. I presume it is lack of lubrication (machine was bought second hand), and I am not sure if the headstock should be filled with...
  15. Re: SL-40 DRO Does not display current tool position

    Thank you for all the replies.
    Having the DRO to update with the current offsets was all that I wanted, and it seems (strange to me) that is not possible.
  16. How normal is the noise made by decelerating from 2400 to 0rpm in a SL40?

    I normally only work with small lathes (max 250mm diameter/10").
    Currently I am making my first steps with a SL40 and I am testing several things, including the spindle. This lathe have a massive...
  17. SL-40 DRO Does not display current tool position

    Hello,

    This is my first Haas. In this case a SL40 from 2005.
    I can offset a tool, run a program, everything fine, but I am unable to see the actual DRO coordinates when jogging, even after...
  18. Replies
    2
    Views
    500

    Re: Recomendation about Hurco VSX 330

    Hello,

    If you want to sell your machine let me know.
    Lately we are buying and selling old machines in parts.
  19. Re: Reset x2 led, what can it mean on a 611 Simodrive

    No I sold the machine just about when I post this on the forum, and I believe that I never found the digital documentation.
    The only documentation that I had were with the machine itself.
  20. Replies
    5
    Views
    436

    Re: Removing backlash on a large double nut

    I was the last hour inside the machine but it payed off.
    I removed the screw and the two nuts disengaged without any ball lost. Thigh them up against each other until the preload is ok. Now is time...
  21. Replies
    5
    Views
    436

    Re: Removing backlash on a large double nut

    The backlash can be felt by hand so it is too much (one hand in the screw and the other on the nut).
    I agreed that is strange that the backlash is almost constant, and I am sure that the support...
  22. Replies
    5
    Views
    436

    Removing backlash on a large double nut

    Hello. I am trying to repair a large machine 14000 pounds that is in good mechanical condition except the backlash that it presents on the X and Y axis.
    The backlash is constant for all the travel...
  23. Replies
    2
    Views
    500

    Recomendation about Hurco VSX 330

    Hello.

    I have a possibility of buying a VSX 330, but I do not know the machine. It is a travel column machine (that I never used before), so I have doubts about it.
    Anyone have knowledge about...
  24. Re: Plasma table with powermax 105 or 125 and torch heigh control

    Currently I have the plasma table finished with a hypertherm 105.
    I would like to know how can I control the amperage of the hypertherm remotely. This way the operator would use a database with the...
  25. Replies
    5
    Views
    672

    Re: CNC Lathe best setup with CAM

    Thank you for the reply (once again). I will look about the conversational that I saw it before on the lathe, but never used it. Nice to know that others do all the work on a CNC lathe, although I do...
Results 1 to 25 of 328
Page 1 of 14 1 2 3 4