Search:

Thanks, that makes things a bit more clear!
As I want to drive the motor with ordinary relays I made a small drawing,
Do you thinks this will work?
339252

A customer uses a Haas Micron VCE1250,

The chip conveyor of this machine is original switched on and off through a board. This part of the board is burned, so the chip conveyor is not working at...

please start up the control while depressing the button "P" "Q" and "Can".
Keep them depressing until the control has started completely, after this, try carefully....

M50, pls put the coolant to "AUTO"

Hi Pep,

Sorry for the late reply, thanks a lot for offering your help.
I got the parameters from WIA Korea, great service!

Hi,
I'm lookinf for a complete parameter list for a Kiaturn 21
The machine is from 1996 and has a Fanuc OT control.
Due to a broken I/O board the complete memory was lost, and there are no...

You can run the program in Tape mode, using dripfeed software.

Older Kitamura's have a small toggle switch called: Manual Absolute. Please turn it on.

You program a "stop" just before the tool call, This stop is because you have to change the tool here by hand, as the machine doesn't have a toolchanger, unless you have a Maho 600E.
Try to program...

Do you program a Tool Set before the tool call?

No it was not the serial number, not the phonenumber not the faxnumber, not the drawing number.
It was really not an easy number.

@tmbruno28,
Got it great, thanks!

Hi,
Does anybody know the code for editting the PMC ladder an a modern Leadwell?

Thx!

Ok, thanks a lot!

can anybody please explaine me the difference between a:
A06B-0859-B192#0E00 spindle motor, and a
A06B-0859-B192#3000 spindle motor?

Its because i have a broken 0E00, and i can get a 3000.
I...

We use a Hitachi Seiki with a Siemens/Hitachi Seiki control: seikos pc flexi.
This control is based on a Siemens 840Di control. (I believe)
After the back-up battery broke down the machine...

try parameter 909#3 to 1

I remember we have a few years ago the same problem with a 11m control.
After contacting Fanuc, the askes me to check "content of memory". There was this data as a binary code. They point to the...

Thanks for all the info.

The Fanuc machine is brand new, the Haas a few years old, thats why I want to use the rotary table also on the Fanuc machine.
It will be a big thing to get it to work,...

I have a HRT 160 Rotary table, with a DC-brush motor, that I would like to run on a machine with Fanuc 0i control.
When I open the front, I can see the back of the motor, its the 20.11.1.36-4175B...

its the very first option, bit 0....

In MDI:

T02:
G91 G28 Z0 M06:

If seen this before.
Depending if its a 18T or a 18iT control, use a ram card, or a flash ram card.
Start up while depressing the left to softkeys.
Backup, one by one all files at the section,...

Looks like the axis controll card is broken...

Any Kitamura has a small switch for releasing the 2nd limit switch.
Its the only switch that you have to keep up, otherwise it wil switch back automatic.
Ok, hold this switch on, if things go well,...

You wrote, you fill in the absolute position in the G54 offset.
This is where it goes wrong, you have to fill in the 'machine' position.
You don't have to hit x, y, or z origin. This wil set your...

Hi Tom,

Its a very old one, i'm not sure if there is a G54 in it. It could have be an option in those days.

What you can do, first go to zero return position, and than put in your program...

Yes, your right, i was mistaking with 16/18/21 series, they use the same numbers (9020 up), but the memory is doubled.

ChamferingCornerR



901 # 1 Tape memory length320M = 128 k. This is 9 out of 10 times the max, withouth adding extra ram. (also quite simple, you can buy them on every corner:D)

Older Kitamura's have on the electrical cabinet a punch tape reader.
Open this, than you will see a switch at the site, be sure to switch this to 'EXT'.