Have you looked into MA Ford or Fullerton?
Type: Posts; User: jreynolds5
Have you looked into MA Ford or Fullerton?
What is your depth of cut?
Why not get a 7/64 collet. With collets just because the range is that large does not mean you should use the full range
As far as this goes, if you can get a print out of a program you are currently running and start analyzing what it is doing. Get the manual and go through the various codes and make notes as to what...
The G09 doesn't cause a hard stop, it is a split second stop if it actually stops at all.
I have also included some more screen shots of the other option tabs for rouging. There are even more...
I mean what other way would you calculate feedrate for milling??
So most modern CNC machines have a look ahead function. Sometimes when running through extensive code it will not slow down and...
PM= Per Minute
PT= Per Tooth
And yes that is what const removal rate does. Now mind you this is probably about $15k or so just for the standard milling package. But you can do things like...
Actually G09 is liie a precision stop, not a physical stop. It makes the program pause for a moment to 'catch up' to itself before starting the next move. It really helps with precision machining of...
I would contact Motor City Spindle repair. They may be able to repair or replace it for you.
We usually just use a standard variable # on our lathes. We put it at the beginning of the program and on each set up they just put in the number. So for this I would put this at the top of the...
I would add the line of code in blue. G50 is modal so if you had a spindle speed limit set in another program of anywhere else it will pick it up.
$2
G710W1
G720U1
P17(BIG_HOLE)
That would mean there is something wrong with that line of code. Can you post that operation??
Do you have a G50 s500 somewhere limiting the speed??
There is no picture. I believe more than likely it will be a Mitsubishi control.
We use Iscar VCGT for most of our turning. We also use the PSZ Turn holders from Sumitomo. They are a quick change holder made by a company in Germany. For boring we use the Picco Ace holders and...
So yes the Double taper bushing is like your bottom picture. Ours were 2 pcs with springs between and rubber rings in the 2 od grooves. Due to the way these clamp with the double taper they are made...
What I mean is it is like the bottom right picture with a double taper on the OD and it had to separate cylindrical pads on the ID both identical sizes. This system uses a pneumatic clamping system...
So the system we were using is the Adaptive Guide Bushing sold by Citizen. It utilizes an air clamping system with a double taper guide bushing that can be clamped and unclamped with an M code. The...
We used to use an adaptive guide bushing on our swiss because we make a long ball screw that is has a rolled ball groove. This part has 2 cross holes thru it with a tight true position. We used to...
So here is a couple of things to consider.
Material:
With a swiss your part is only going to be as good as your incoming material. On average if your material has .001 of runout you generally...
Why not just use a rotary broach?
As the title suggests I am trying to cut Cronidur on a Swiss machine. So yea I am having all kinds of fun. Looking to see if anyone here has ever done the same, successfully? My issue is tool life is...
Below is a program example of a .02 rad into a 20° angle. should be able to use the same concept for your double radius. This then goes back in Z and does another 20° angle, because I am sure someone...
You do not need to zero return them, If you turned them on with any doors open or anything, and you may have to have a bar feeder hooked up too, it will throw all kinds of alarms.
We have an A320 that we used to have an adaptive guide bushing installed on. We run a ball screw on it that is about 25" long. Every since we started running this part we have had issues holding a...
I would say you would want to maintain the same tolerance of the material that you do for brass and aluminum. I cannot help with supplier info I am in the US
The top 2 in the industry are Citizen and Star. Either one will be able to achieve thread whirling. I would check to see who your local distributers are and see what kind of reviews they have for...
So we are looking at purchasing one of these 2 mills very soon. I am looking to get some pros and cons for each from individuals that have experience with either of these machines. Thanks in advance.
Thanks for the reply. I cant remember what I did I did get it working a few days after this post. Then a few days later the backup battery died and wiped the memory lol The joys of doing side work on...
I am doing side work with a local small shop. I am working on getting a Miyano BNC 34T programmed and running a simple part. This machine is unfamiliar to me and there in no one there that knows...