512,476 active members
2,621 visitors online
Register for free
Login

Search:

Type: Posts; User: Tedger

Page 1 of 4 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    80

    Re: Tool Not Releasing

    See attached for Bellville info
  2. Replies
    4
    Views
    80

    Re: Tool Not Releasing

    There is rectangular aluminum plate that is attached to the pin that pushes down on the drawbar. The Plate is actually the moving part (Piston) of the air cyclinder. I have had these crack and leak...
  3. Thread: Vmc 15xt

    by Tedger
    Replies
    3
    Views
    77

    Re: Vmc 15xt

    Check your parameters. Type "SETP" and scroll through the options on travel
  4. Thread: CL access code

    by Tedger
    Replies
    4
    Views
    94

    Re: CL access code

    Perhaps yor parameters are wrong. Can you type "SETP" at the command line to double check them?
  5. Replies
    5
    Views
    105

    Re: Smoke after Spindle turn off

    Yes. The low air pressure most likely caused your problem. You now have a burnt spot on the low speed belt that will cause vibration and noise. It should probably be replaced.
  6. Replies
    7
    Views
    127

    Re: 4th Axis Inhibit wiring

    Go to "FADALCNC.COM" click on "Technical docs". In the lower left you'll see the Header for Wiring diagrams. Click on 4th axis servo options. Page 5 shows you the wiring diagram for the inhibit...
  7. Thread: Jump lines

    by Tedger
    Replies
    2
    Views
    122

    Re: Jump lines

    You are correct. You cannot use "R" as a label. You need to use "L" to designate how many time to repeat sub
  8. Thread: Hello everyone

    by Tedger
    Replies
    3
    Views
    186

    Re: Hello everyone

    Will this Help?
  9. Replies
    4
    Views
    300

    Re: Fadal VFD Choice ??????

    AMC will repair it if it's not to old. Give them a call
  10. Thread: X axis fault

    by Tedger
    Replies
    7
    Views
    475

    Re: X axis fault

    I've never blown the fuse on the amplifier.If your blowing a 20 amp fuse, I wouldn't suspect the control board. Either something in that amp is bad or maybe you have a short in the motor or a short...
  11. Thread: X axis fault

    by Tedger
    Replies
    7
    Views
    475

    Re: X axis fault

    The Axis control cards are the ones in the slots 9,10 and 11. The picture you have shows the axis Amplifier. There is one for each axis. The control cards rarely fail in my experiance. That means you...
  12. Replies
    26
    Views
    1,451

    Re: Digitizing a head port

    "I am using A 2008 haas vf3 with a 2 axis trunion table. We probe ports, chambers ect in 5 axis mode, using master cam to drive the probe . I had a custom post that was writting for my application by...
  13. Replies
    7
    Views
    334

    Re: Fadal VMC 15XT z axis move by hand

    7/16" - If you drop the way cover, make sure you clean out all the chips packed in the bottom.
  14. Replies
    7
    Views
    334

    Re: Fadal VMC 15XT z axis move by hand

    Yes, If you can get to it. It might be easier to remove the 4 bolts holding the Z motor on and rotating the coupling to lower the head. Use a sharpie to mark how the motor clocks to the ball screw or...
  15. Thread: vmc15xt issues

    by Tedger
    Replies
    14
    Views
    582

    Re: vmc15xt issues

    There are places that can test and repair your old drive. may be more cost effective if you have the time.
  16. Replies
    4
    Views
    342

    Re: VMC 4020 Z-axis brake

    You say you just bought it. Check the counter weight in the back for a shipping pin. These were installed to keep the weight from moving around. Should be about an inch or more in diameter and held...
  17. Replies
    1
    Views
    148

    Re: VMC15 Spindle Air

    Never saw spindle air on a little VMC15, But all the ones I saw were 7500 rpm. It looks like they relocated the Tool changer regulator to right under the valve.
  18. Replies
    4
    Views
    571

    Re: 1400-5A vs 1400-5C CPU board

    Well,I looked it up and you are correct. You can only use PCB-0041(384K) on the 5A .

    For the price people are charging for additional memory expansion. I would much rather purchase a calmotion.
  19. Replies
    4
    Views
    571

    Re: 1400-5A vs 1400-5C CPU board

    I have a 1400-5A with 4MB expansion. I never heard that the memory wouldn't work with the different revision letters. As long as it's a 1400-5, you should be good to go.
    Here's a compatibility...
  20. Replies
    12
    Views
    1,068

    Re: Good Buy Fadal VMC40

    That's a good price for a machine that was rebuilt 3 years ago. Especially if you get some good tooling with it. Fadal's are not very fast but they are pretty reliable and cheap to repair when the...
  21. Replies
    4
    Views
    568

    Re: Fadal 4525 any good?

    No. It has the Fadal 88HS control
  22. Re: Fadal vmc 15xt losing parameters and what to look for purchasing

    Fadal offered an air filter kit that sat atop the spindle (MTR-0128). You could also make one yourself with a properly sized auto air filter and a round piece of sheet metal with some longer fan...
  23. Replies
    1
    Views
    285

    Re: Fadal swing arm changer

    If you type in DD you can see the bucket number and tool number table. The asterisk shows the current bucket at the ready. SETTO will clear everything and re-synch tool and bucket.
  24. Re: Fadal vmc 15xt losing parameters and what to look for purchasing

    Tight fit! do you still have the servo coolant control bracket?
  25. Re: Hyundai Hit-18s with siemens 840c ERROR 9107 axis motor overtemperature

    Good idea. Caps don't age well. Glad you got it sorted
Results 1 to 25 of 95
Page 1 of 4 1 2 3 4