Search:

Fixed the variables = null

Changing the M30 to M02 showed me the variables.

M30 stops the program and winds the tape. Leaves the machine completely reset state and clears the variables.
...

Don't know what I'm doing wrong.

For a test I ran

%
:0040 (OFFSET ADDRESS)
#100=100
#101=#4120
#102=#2000
M30

I have an OMD.

G43 H# moves the axis immediately to the preset value. Can be quite dangerous if at Machine 0

I'm tying to move the Z to a safe point before implementing G43 or cancelling it...

Tried various options but can't enter # in MDI mode directly. Can in a line like below.

Tried G65 H1 P#100 Q20 (#100=20)

but get an error. From memory 078, something like cant find program...

I'm missing something here

In my macro have

#106 = BIN[#1032]

I assume that #1032 is the next tool number

IF[#106EQ#20]

Thanks for the reply.

I'm still learning and still to find info on the # numbers. Any suggestions where to look ?

I know that #20 is my next tool number.

Here is my macro for my auto Tool...

Hi Just wondering if this is still active. Just refurbished a YANG SMT500 It has an OMD controller and the tool offset has been a real problem. Nearly broke my machine when I used G43 H2 with a 30 mm...

I've rebuilt a YANG SMT500 and busy with commissioning it.

I'm new to the machine and never actually run it before.

The tool changer has 2 issues.
Stops mid code
Sometimes a loud crack when...

I'm not so sure that 087 is an exact alarm. I think it merely means that something is wrong.

I can download the parameter file which is very long with 3 wires, no hand shaking without a problem....

I believe that drip feed needs 5 wire.

Has this anything to do with alarm 087 ?

Thanks, would never have found that.

Evaluating EZ CAM. Old user of Sheetcam but with my new machine, I need an upgrade,

I've opened a DXF drawing and have one profile. Outside-5 as shown in the picture. From the training videos,...

I presume you have the parameters in a file.

From memory, I had to enter P0900 and P0901 parameters manually and then I could load via the serial port. (Special Parameters go from 0900 to 0932) ...

From memory I was writing 9000+ programs

Once I change the parameter to give access, all worked.

I also changed to a 5 wire serial cable from 3.

One or 2 of the above fixed the problem.

Thanks. This is for a later model but I presume the basics are the same.

Hopefully this post is still a live.

My new second hand machine has X and Y moving in the wrong direction. Table toward the door and table left is +ve.

It has home switches at the + ends....

I have a FANUC OMD and after the battery power was lost. Had to reenter the parameters, PMC and macros.

I cant however enter the macros 9020 and 9021. Have set parameter 0010 # 4 to a 1 but still...

I have the same problem. Error 071. I don't have a key but a bit I can set on the CRT. It is off. Fanuc OMD

I can up and download all the parameters and diagnostics without issues.

It...

I cant seem to find what document I actually need to learn about the ladder in my OMD controller. There seem to be so many search results but non on what I need. Is searching for Fanuc OMD ladder....

Here are my screen shots.

Not sure what and how to enter data. Seem to be able to enter some info.

489242

489244

Thanks for the explanation. I'll be doing similar. I'll keep in mind the runaway but hope I never get there.

I'm just getting into Fnuc ladder so I have a bit to learn.

My data register G119.0 -> Ladder display. Currently I'm not allowed to view the ladder.

Here is the ladder. Haven't quite worked...

Interesting, my wire numbers from a YANG machine are very similar.

489208

I'm away for a few days, but will give it a try when I get back.

Which are the FANUC eproms and the machine builders ?

489170

I can't believe that 1100 people have looked at this post. What an active forum.

I have some movement on the machine when I press and hold the EM button. I get a contactor come in and then a servo...

I am part the way through a full refurbishment and machine is partly disassembled. X and Y are now done. In the mean time , we lost the memory but hopefully have got the right info in the Fanuc OMD. ...

I need to manually rotate the Z drive. It has a brake on the servo motor. I cant find any details on the electronics of the drive. From the schematics, it looks like it could be 90 volts AC.

According to my OMD manual Parameter 19 bit 7 is DBCD. If = 1 the timer/counter values shown in Decimal
If = 0 then binary.

The original value was 1000 0000.

Cant enter by hand or cable.

Looks like these are protected. Any idea on how to unprotect ?