Maybe just me, but those pictures aren't viewable.
Maybe it's time to try the rick repair guy?
Type: Posts; User: erikfriesen
Maybe just me, but those pictures aren't viewable.
Maybe it's time to try the rick repair guy?
Is your g52 0? I learned this the hard way, renishaw s0 sets g52.
Post your program. Something sounds a bit wrong. Sometimes when batteries go out or a chip gets stuck in the tip funny stuff happens.
As far as putting it on, it's not a big deal with an 07 machine I would say. Worst case you could buy a new io board that matches what Haas has on the receiver. I just found matching connectors from...
If your hfo is willing, they can sell you the package including macros, rotation and scaling for the $6k range pricing. At least mine did for me, although they basically let me know(I didn't ask...
Are you wanting to stay with some type of floppy interface? Or use rs232? One factor is whether or not your machine supports the 115k rs232 rate.
Some flukes have a min max feature that might work. The best of course would be a scope. Can you get Haas to prove it perhaps? I know with phase converters it's sort of a guilty until proven innocent...
It would be easier with a haimer. Then you would zero your cat40 measurer on z zero in the haimer. At that point, you will then set work offsets with the haimer and the set workset offset button. One...
Have you showed HAAS the blued taper? It really is going to wallow around bring so tight at the top.
There is another op amp that needs to be replaced besides the 7800 chip. If it is damaged you'll get a negative voltage like that. See the schematic on the web the guy posted . LF411CD I think. At...
I had my spindle rebuilt by setco. It was around $4300 with a 1 year warranty, and I did the install, its a couple hour job probably.
Is the air purge working correctly? Even though it is grease, Isn't there is some mechanism to keep coolant away from the bearing?
Is it the fuse after the mov? You could try a power logger to see if you are getting too high voltages.
Also note that you should always use the probe in the same orientation, IE not 180 degrees off.
You could try the raw renishaw routines.
You can look them up in the manual too.
G0 G90 G65 P9023 A10. D1.0
Sets center on a 1.0" ring from wherever you start from. D is the diameter of the...
Have you checked your relays and fuses?
Is that a new thing, or some canadian difference? That isn't the way it is here, at least last time I had the haas tech here. All the boards come without software loaded.
What is the line item for $12k? The maincon lists on haasparts for $3,500. Did the tech try reloading the software?
Maybe I missed it in this thread, but rapids really don't make a machine shake, it's your Accel/decel params that make the most difference along with some other obscure params.
Hold the program conversational button and hit power on.
Be careful though, you could brick your machine if not careful in that screen. (Or brick without HAAS help)
If centering of the stylus to .0001 really is only so you can use it both directions. If you always face it the same direction, it isn't as critical.
Are you entering a diameter value somewhere with the wips page?
https://diy.haascnc.com/diy-search-results?term=Wireless%20Probe
https://diy.haascnc.com/sites/default/files/Locked/3/RENIPS_V30.nc?0=%253F102
It still seems a bit obscure what you mean by Z offset. Assuming you mean tool offset and not probed offset, the way I have done similar is to pick a work coordinate you don't use for anything else,...
Do you mean as referenced against the ips tool setter or what?
Que quiere decir por "sub-source commuted" ? Tuvo que cambiar partes del vector drive or otros?
Which number alarms?
There is a count difference if you are changing from old to new style, 8000 vs 8192 for the new.
Hay una diferencia entre el Nuevo y Viejo, El neuvo tipo tiene una cuenta por revolution de 8192, y...
I changed params 79 and 239.
on mine, 79 = 4096, 239 = 8192
What year is the machine? My 96 vf2 complained about this until I set the count per z to 8000 and the counts per rev to 4000. It because of the 2:1 gear belt ratio.
De que parte de Mexico?