Search:

I believe the Actual cost of the retrofit, was about $10,000.00.

After years of trouble trying to get.our router working with camsoft we bit the bullet, and retrofit the unit with centroid. All the troubles, that we had with camsoft, turned out to be ****ty...

Hi, When I program a small rectangle to be routed in a plastic product, the rout is bigger than I programed, as the bit is cutting on the center. I want the bit to be offset left. The manual says to...

We retrofitted a multicam mg, with centroid software. works great

Has anyone ever answered your question about assertion failed?

I am trying to program a series of hole that have a drill bit/countersink built in. I would like to have 2" of z height clearance. How do i make the spindle rapid down to about .200" and slowly drill...

I recently had the camsoft control replaced with Centroid, and now the cnc router works perfectly. There was no issue with the motors or encoders. they currently hold perfect repeat ability. The...

My post processor, is not powerful enough. When it generates code, it travels at one speed throughout the whole profile. Some of my fixtures cut 10 or 20 pieces at a time per cycle. It would take...

I am looking for a post processing software, so I can speed up cutting speed, when cutting straight, and slow down when cutting corners, radius's, and arcs. I currently use enroute 5 plus, but they...

I currently have Enroute 5 plus for post processing of dxf files to generate g-code for our cnc router. Enroute says that they don't offer a way to slow the cutting speed down, when going from...

You got support? every time I ask a question, it takes 1 or 2 days for an answer. Most of the time the answer is to send them a check, and they will fix it. I have been working with them for 5 or 6...

It always took 1/2 to 1 second for the computer to respond, but 15 seconds is a long time. It was much better with the old version 17.2. Camsoft is going to send me the latest version, to see if it...

I installed the latest update to cnc professional level 5, version 17.4, and now when I use the pendant to jog, or change axis, when I press a button, it takes 15 seconds before the machine responds....

I use Vance Industrial Electronics, in Burlington, NC, for all my Kollmorgen repairs. 1-800-360-1992:wave:

I am trying to rout a keyhole shape in plastic. The hole part is choppy. I am using camsoft cnc pro level 5. any ideas where to look to solve the choppy hole problem?

I am trying to drill some hole centers, and when I merge the contours, The only drill icon that comes up is drill point. On my old computer, drill centers would come up. I am using autocad mechanical...

The encoder has 6 wires. The cable is factory made, with a molded end, that plugs directly into the yaskawa amp. We recently had the router retrofit, and some of the wiring, runs along with, or near...

I have a servo motor system, with motor mounted encoders. The x axis is gantry type, with master/slave motors. The y and z axis are both driven by servo motors with timing belts, and ball screws. I...

I have a cnc router. It used to be multicam, but we retrofit the unit, with camsoft software, and a galil motion card. The software runs well, and has plenty of options. The problem I am having is:...

I upgraded from cnc plus to cnc professional level 5. Now one of my one of the servo motors on my gantry says it is turned off. I try to move the x axis and an error comes up motor 1 is off, cannot...

The servo motors that move the gantry, Xa, and Xb were not tuned properly by the people who did our retrofit. They had one motor set at 52.3, and the other set at 23. I, (through trial and error) set...

I recently had our multicam router retrofit with a camsoft software setup. I need to find out what the ratio is between the servo motor, and the rack and pinion gear setup, and also the motor and the...

I have a servo motor system, with encoders mounted directly on the motors.

Did you ever get your driver? I have a multicam MG 204.

How do I get the proper ratio to calibrate my newly retrofit cnc router?
When I run multiple cycles, the Y axis seems to move over a little each time, and after a few cycles the parts are out of...

The router was manufactured by multicam. serial # MG20442986.
We had this retrofit last year, and the techs never worked out the problems completely, and took about 1 year to do the job, instead of...

I recently had our cnc router retrofit with camsoft cnc plus. When I jog the gantry, (servo motors Xa and Xb) the gantry starts to move smoothly, and then starts to shake. Its almost like the...

I meant, when I try to intialize the machine, the buttons become inoperable. the only way I can get them to work again is to turn off power, and then start again.:confused:

When I sty to initialize the machine, is freezes, and the buttons become unresponsive.

When I try to start our robofil 300 it does not intialize. I think we had it turned off too long, and lost the startup parameters. Anyone know how i Can reload them?:confused: