Yesterday I began to hear some noises from my spindle motor - a high frequency "whining" or "whistling", it's intermittent and varies depending on speed. So I suspect the bearing - how easy are those...
Type: Posts; User: dynaflux
Yesterday I began to hear some noises from my spindle motor - a high frequency "whining" or "whistling", it's intermittent and varies depending on speed. So I suspect the bearing - how easy are those...
I'm using Fusion 360 so I will try this. Thanks!
I have rebuilt my Omio X8-2200L-USB with a CNCdrive AXBB-E ethernet motion controller and then running UCCNC. Prior to conversion I had problems with loosing steps, now it works really nice. However...
Forgot to say: running Mach 3 on Windows 10.
I have suddenly encountered my machine (a modified Omio) sometimes goes to far in X. Yesterday I routed a piece were there should be a square hole in the material but suddenly it went too far to...
I bought my Omio X8-2200L-USB three years ago and used it on daily basis for my work. Generally I'm satisfied with it but sometimes (but still seldom) it steps wrong so after a recommendation from...
I have used a Omio X8-2200L-USB for 2-3 years and since day one there have been problem, it "oversteps" sometimes - it occurs in a few percent of the runs so it's hard to fault seek. Typical some mm...
Hi, I think I may have the solution. I opened up the control unit and everything was covered in dust. Just when I was cleaning it a friend dropped by, he is a electronics engineer and he gave me a...
Have anyone had problems with losing steps on Omio? I purchased a Omio X8-2200L-USB more than an a year and have used it on daily basis without any problems. However, last week it began losing steps...
I have owned a Omio X8-2200L-USB for more than an a year, using it on daily basis without any major problems. However, last week it began losing steps on Z, not often but all of a sudden when I don't...
My Omio X8-2200-USB has been running perfectly for months but today a clanging or rattling noise occurs when I jog the X-axis back and forth. It sounds like the aluminium plates are loose, as they...
I have tried that. Then the spindle goes down instantly. Luckily I held my hand on the emergency button.
My temporary solution is to put "G0 Z5" before "G0 X52.6 Y26.2".
(1001)
(T1 D=2. CR=0. - ZMIN=-3. - FLAT END MILL)
G90 G94 G91.1 G40 G49 G17
G21
Ok. I don't have the time, knowledge and stamina to sit down and analyze the code. I'm busy trying to learn understand G-code.
From zero but it doesn't rise before going to the starting point and...
I designed in Fusion 360 and imported G-code to Easel. For my new Omio machine i design in Fusion 360 (even same files as on the X-carve) and run G-code from Mach3.
"Origo".... this is a term in...
I haven't succeded in getting my Omio X8-2200L-USB to behave correctly - I need to modify G-code prior to every job. I use "CNC Router Parts (Mach3Mill)" post processor in Fusion 360 and haven't been...
I suspected that. But why did it rise when I ran same files on my X-carve? It uses an web based application (Easel) where you load the G-code - is it possible they have made an idiot safe tweak for...
When I set the bit on origo it doesn't rise before it travels to the starting point - just draging on the surface. Is there any setting for this in Mach 3? I had a X-carve where it rised to safety...
Should I go for red, green, yellow or blue? Does it matter? I have heard some types can damage rubber seals.
In the manual for my CNC machine it's recommended to pour anticorrosive in the cooling water for the spindle. I have searched for anticorrosive but can't find any general product (unless you buy a...
Made notes straight away. :-) Even if you think you will remember there is a good chance you'll go through the same process next time.
Problem solved! Some of the configuration files appeared in wrong folder when copied to the installation, the instructions were ambigious (and I went with the wrong alternative).
Yes, quickstart which I followed in detail.
Plugin? USB motion card?
Emergency button disabled.
Today I tried a third computer - and it worked. Can't see I did something different. But I...
I purchased a Omio X8-2200L-USB some weeks ago and can't get it working. I have installed Mach as described in the manual, everything is correct connected, control box is alive but nothing moves. The...