HI,
There is some problem in operator panel so I want to change its operating panel by local made.
How can I take Ladder back up & then can edit it.
BY PCIN -- Ladder software downloaded but...
Type: Posts; User: rajesh_1355
HI,
There is some problem in operator panel so I want to change its operating panel by local made.
How can I take Ladder back up & then can edit it.
BY PCIN -- Ladder software downloaded but...
HI,
There is some problem in operator panel so I want to change its operating panel by loacl made.
How can I take Ladder back up & then can edit it.
BY PCIN -- Ladder software downloaded but...
Dear Fiends,
In my Makino A77 with Fanuc 16MB, facing problem during pallet change.
After Input M60 & Cycle ON
On APC operator Panel --
Step 1 -- Pressing "Man P.B ( Input X2.3)"
Step 2 --...
For changing locked parameter, you will have to delete all parameter & start from loading optional parameter in Fanuc 10, 11 & 15 system.
Before deleting pl take a full back up of machine data, plc...
Good to know..
Dear Respected members,
I have a OKUMA Howa make turning machine model HL JR with Fanuc 21TB controller. I have lost its data.
Any good person can send me SRAM data or hard copy of dtata at --...
Dear Respected members,
I have a OKUMA Howa make turning machine with Fanuc 21TB controller. I have lost its data.
Any good person can send me SRAM data or hard copy of dtata at --...
Dear Sir,
I read your thread .
I also have Fanuc Tap Drill Mate Model T( NC Type- Fanuc Series O-M Model C ) , but I have lost its parameter, can u pl help me by sending the machine parameter &...
Dear Sir,
I read your thread .
I also have Fanuc Tap Drill Mate Model T( NC Type- Fanuc Series O-M Model C ) , but I have lost its parameter, can u pl help me by sending the machine parameter &...
Dear All,
While running machine in constant cutting mode G96 -- Spindle RPM are varying with radius reducing but Feed ( Actual ) - remain constant
Resultant in increased cycle time.
Any...
198732Dear Genius ..s,
I have a favour , I have a MAZATROL QTN - 20 H-P.
It showing alarm -- 322 Rapid Mode Imp. ( ORIGIN RETURN UNF ).
As soon as mc is switched ON - normal screen flash &...
Hi Bill,
Thanks a lot for your sharing.
Definitely I m going to try this tomorrow.
Thanks A lots once again.:wave:
Dear Friends,
I have Cincinnati VMC with Fanuc 21 m controller. while running prog for rigid tapping, quality of thread is not good.
Here under is the programme,
N1
G0G90G80G40G21 ...
is it direct couples or belt driven,
if it is belt -- use belt dresser spray ( if not timing belt)
If timing belt --check belt teeth
if direct couples -- try to replace the pulse coder sensor....
if it is fanuc 15ma
here is the password
23678625
37264699
19261161
enter these after pressing 99
rest procedure is similar to fanuc 10
Dear Friend ,
I received no reply,
pl note that F-rom data is easy to take back from machine similarly like Ladder back up.
Just press 2 buttons below the screen ( both extreme end -- extreme...
DERA FRIENDS,
I faced Error " Ram Parity " on machine.
Found its SRAM card defective,
In the process lost FROM & PLC ladder .
Need help -- if any gentle man have the same machine , pl help.
...
DERA FRIENDS,
I faced Error " Ram Parity " on machine.
Found its SRAM card defective,
In the process lost FROM & PLC ladder .
Need help -- if any gentle man have the same machine , pl help.
...
Thanks for the reply sir memoryman.
There are 3 door signals
1 = Operator door ( input checked = 1 its working )
2 = ATC door ( input checked = 1 its working )
3 = Pallet door ( input checked =...
DEAR ALL,
FACING ALARM: LS 924 = 0 WARTEN AUF TUER GESCHLOSSEN. MACHINE IS HMC - MAKINO MC 50.
FANUC 15MB CONTROLLER , PL HELP ME TO SOLVE PROBLEM. I DON'T HAVE ELECT DRAWING. WHAT IS THE...
it works in dos only.
Hallo.I"m from Rajesh .I need manuals in english for Mazatrol Cam M-2, Please help me
thanks in advance.
[email protected]
ALARM: EMERGENCY EXIN
M01 OPERATION ERROR XZ
Detail of machine are as under,
NC - MELDAS MAGIC 64L
PC - MAGIC Pro-HI/L ( INTL) BDD - A02 W016 - A0
PLC - ECOCA - ELALL -...
Dear John,
Pl help me , I am facing problem in same type of machine.
[email protected]
Thanks:bs:
sir, what I feel 9020 is not a problem.
I hv tried all possible combination of 9020. Above one also.
As soon as machine read Txx code it shows Alarm 201 & Magzine does not rotate.
May be some Tool...
Dear Sir,
I tried many combination suggested in this forum for tool change prog 9020 but could not success-ed. Actually this machine is MORI SEIKI - MV 40 S WITH FANUC OMC. I tried to understand the...
Dear I downloaded it from machine when in good condition. I don't know how it got corrupted. Pl suggest some remedy to run the cycle. Its Mori Seiki Fanuc OMC machine.
Do u have detail of Micros....
Dear Friends
(MACHINE: MORI SEIKI-VMC-FANUC OMD)
In my machine alarm 901 appeared few days back, found its memory card defective same got repaired & reloaded the data. Everything is running ok...
Thanks repair (great) man
DEAR FRIENDS,
FACING A PROBLEM,
MAZAK VMC WITH FANUC 11M
MACHINE WAS OFF FOR 15 DAYS
WHEN SWITCHED ON & CHECKED THE MC, FOUND ORIENTATION NOT WORKING.
FOR KEY LOCK KARODA MAKE ENCODER IS...