Search:

The wiring diagram I have shows K29 Green Strobe connected to Pin 9 and 10 on connector P3 of the i/o board, and K30 Red Strobe connected to Pin 11 and 12 on connector P3 of the i/o board. Both these...

I'm in Essex, I am thinking about totally reloading the machine as I think something corrupted when loading. The machine type was not set in debug mode when I reloaded all the parameters and settings

Had to re-initialise the machine after total loss of parameters due to no battery. Have replaced the battery and set the machine type using Debug. Loaded up the backup but have noticed setting 26,...

I am using a dongle licence on my PC and when I load camworks it cant find the licence. As far as I can tell the licence device is up to date, but the driver seems to be looking to the internet to...

I might be able to do this, email me at [email protected] if you have not already found someone

index

Richard

I am getting alarm code 475 real time clock cannot be found on my MM2, does anyone know if this is tied up with the on processor board battery or a sign of something more serious ?

Tried it this morning with the original dual screen set up and up popped the stock manager window. Don't know why it did not appear on the second screen that I was using at home. I had gone through...

I have tried with both dual monitor and rebooting with only a single monitor, im convinced the window is open somewhere as I can do nothing when it happens, pressing escape closes the window I cant...

Im using Solidworks 2013 with Camworks 2012 and have a new issue. When I go to the Camworks feature tree and edit my machine, that works ok so I know its found the Tech DB ok, however when I go to...

I am about to look at one of these machines as a 5 axis entry level machine. Anyone with experience of this machine care to share their thoughts on good points and bad points

Richard Marsh
RRb...

Does anyone have a PDF manual or a link to one for this machine ?, I cant seem to find one anywhere

Richard Marsh

What files do you have ?, do you have the .SRC file or just the .CTL and .LNG files

Do you have any drawings you can send to [email protected], I am based in Southend on Sea area

mail me at [email protected] with your details and I will arrange to quote

regards

Richard

I can do these for you, mail me at

[email protected]

regards

Richard

mail me at [email protected] and we can maybe give you a price

Richard
RRb Machining Services

what is the model drawn in ?, you may find that the fault is in the model with surfaces being transparent, thats why Camworks machines through them

We would be happy to quote if you can send any more information to [email protected]

Richard

It was mechanical, I dropped the drive belt off and tried it and the motor run under no load. Tried turning the drive sprocket by hand and it had virtually siezed, so it was time to strip it all down...

has this work been awarded, if not we would be happy to quote

Richard
[email protected]

if you can email details to [email protected] we will be happy to quote, we are based in Southend on Sea Essex

Richard

When i post processed the part there was no G41 / G40 codes in it. I have now found the option in my cam (Camworks) to turn these codes on to allow wear compensation to be used. I think just to get...

Thanks Geoff, if I use the tool wear coloum do I still need to program G41 or G42 ?

I have not had to use this before so please excuse my ignorance of this feature. I am milling some pockets for bearings to sit in, so want a good fit. I have been using a 10mm slot drill to open out...

We have a 3 phase drive type Delta VFD075B-023A which is a 230v 3 phase type for US supplies. Our supply here in the UK is 415v 3 phase. So this drive will not work on our supply. The machine...

A Haas tech made a lead up for me, just three wires from the power supply board, P33 plug I think it was to the servo amp low voltage connector. Bar feed interface installed and up and running. It...

I am adding a bar feed interface to my SL20, but the servo amp I have for it is a non smart amp type, all my others are smart amps, so dont have the low voltage cable. I need to add a low voltage...

Is it the tool or the holder that is hitting the work ?, check you have sufficient tool length to reach the areas you are trying to machine. If you send the sldprt file to [email protected] I will...

Thanks for that, the machine I am putting it on is only just over a year old and one of the last SL20 made, the feeder was made in 2007 so hopefully it should not be a problem

Does anyone know how easy it is to fit a barfeed interface to a SL20. I have been offered a three year old Haas Barfeed and the owner wants to remove the interface from his SL20 and I am looking to...