Just got the same machine. Any chance I can message you with some set up questions?
Type: Posts; User: dudesmpd
Just got the same machine. Any chance I can message you with some set up questions?
Just got an E25J machine and I need some help with my first set up. I can't get the #7 and #8 on the attached photo to clear.
Rochester, New York - USA
I have that exact machine setup. that barfeeder alarm will show up every time you power up until you get the barfeeder turned on. once you power the bar feeder and hit switch S73, then the manual or...
Hey all
I am looking for the keypad that plugs into a Freqrol-Z200
the part number is FR-PU01E
Would be great if I could borrow one of these for a day to get my live tooling parameters on my...
I am looking for a Fanuc ADD.AXIS/MEM. board
A16B-1210-0380 A
I am also looking for
A16B-1010-0041/05A
These boards are on a Citizen E32K built in 1986
thanks!
I was wondering if anybody knows the parameter for a Citizen E32 with a fanuc 10T control that enables synch between the main and sub spindle?
The cassette that contained all the parameters was...
I have a Citizen L432 built in 1995 with a Mitsubishi 500L control
In the last couple of days the machine has alarmed out with the following
S04 SERVO ALARM : AR 006C S1
EMG EMERGENCY ...
thank you onthebumber and girishdk for responding.The Citizen tech traced the problem back to a faulty PLG switch.had the switch replaced Friday.Machine ran well all day today,until 2pm...then i got...
I have been getting many servo alarms the last 2 days.Yesterday the machine was getting a S01 servo alarm:PR 0033 S2
Today it was getting the same but the code # was 0042
The secondary spindle...
My citizen doesnt have live facing tools so i cannot use thread milling
I am going to try the tap you suggested
In the mean time,I had a cobalt tap that i was going to see how many parts i could...
Thanks for replying...I'm getting desperate
Yes...the thread is an ID thread
Yes....I am single point threading it with a Vargus threading bar and inserts
I started by using a Citizen swiss lathe...
I am trying to thread some 304 stainless tubing
I have to thread each end of 4300 pieces(8,600 threads)
its a 3/4 x 16 thread in an .875 tube
right now I am single point threading them and getting...
Hi Gizmo...thanks for sending me your question-sorry it took so long to reply
I have had my E32 for 6 years now and I have to say there are more negatives then positives.Most of the problems with...
NAFTA was signed by U.S. President George H.W. Bush, Mexican President Salinas, and Canadian Prime Minister Brian Mulroney in 1992.you have zero facts right and a whacked agenda-typical right winger
apparently maz43 smoked a lot of pot because he lost his long term memory
the current economic crisis wasnt created in the last 6 months by the"liberal"government we just elected.this problem was...
they also make extended land and extended nose guide bushings if you want to rough and finish
your gonna use canned cycles to drill,tap and rigid tap
i ran a shaft that used...
I turn H13 tool steel that gave me the same headaches
what i ended up doing was using a Kyocera DCMT32.52gk- grade 5525
6000rpm and .008 feed
holds a good finish and chips well with high pressure...
could be as simple as the door interlock switch
is the door open or shut when this happens?
is there an m-code to change from low to high gear?
thanks for the info-i'll try them
the Citizen L32 has live tooling.it probably wont take that long to use a key cutter but i don't know anyone who can make the special form an external spline would need.
I wonder if i can roll form...
how would you make an external spline in a Citizen L32
it is .455 major dia and .352 minor
can i broach it?
where can i get the tooling for it?
material is 416ss
the spline is .625 long on a 5"...
i have an E32k with a fanuc 10t
i am pretty sure the m and g codes are the same
my email address is [email protected] if you want some examples