hi, i have a problem with my harrison alpha 400 lathe, im getting a 351 and 414 servo alarm , anyone have any idea of where to start diagnosing this problem?
thanks
Type: Posts; User: brinmac
hi, i have a problem with my harrison alpha 400 lathe, im getting a 351 and 414 servo alarm , anyone have any idea of where to start diagnosing this problem?
thanks
hi , does anyone here by any chance have the sram files for a harrison alpha 400 lathe, mine is s/n a30462 .
thanks
r brintle
hi, im looking for a post processor for a milltronics centurion 6 mill, for version 7 featurecam.
thanks
r brintle
hi, check your limit switches, i had an eztrak that did the same thing and i found out that i had a limit switch that was stuck .
hi, i am looking for the cut settings chart for a fanuc tapecut wire edm machine, my machine lost the parameters and i do not have the parameter tape , i manually entered the parameters but dont have...
hi, i need some help on a fanuc tape-cut wire edm, i had a battery issue and lost all parameters . i have all of them entered and working good except the parameters for the auto cutting condition and...
i have 3 axis eztrak, sem motors, recently the x axis has started jumping and motor running really hot , today i tried another motor and still same issue . after jogging axis the handle will almost...
i recently acquired a cnc flame/plasma table, been using with flame torch but ready to add plasma .
my question is , i have a great pakmaster 100xl machine but has hf start , would it work ok on...
hi, i am looking for the z axis ballscrew and nut , my machine has the old style cantilever arm z axis.
thanks
rbrintle
i am looking for the ballscrew and nut for an extrak with the cantilever z-axis. anyone know where i could find one new or a good take-off?
thanks
r brintle
hi , i am having a pressure problem on a flow machine with cougar 2 pump. when i start pump i can get 40000 psi but as when i turn head on pressure drops to 25000 - 26000 psi and wont go any higher ,...
i need to add that i need it on or i can put it on a 3.5 " floppy
hi , i am looking for a copy of the system disk for an eztrak , i am running version 5.00.21.08 and need to reload it in machine but wont read disk. does anyone have a copy that can be mailed or...
im getting ready to start building a 4 x 4 plasma table , i already have a thermal dynamics 100xl plasma cutter , works great for hand cutting , plenty of cutting capacity for my needs. my question...
hi , we have a full retrofit for waterjet or mill , with up to 8 axis capabilities, that we bought to retrofit a machine and found other problems with machine and decided to scrap it and buy another...
hi , was wondering if anyone had tried using vfd drive on a cougar II pump to increase motor rpm and flow rate for water?
thanks
r brintle
hi , im retrofitting a machine with mach 3, pmdx 126 breakout board and panasonic servo drives and motors, i have movement on axis now , but always in same direction , mach3 displays show correct...
hi , im retrofitting a machine with mach 3, pmdx 126 breakout board and panasonic servo drives and motors, i have movement on axis now , but always in same direction , mach3 displays show correct...
i am trying to integrate a machine with panasonic minas a4 servo drives using a pmdx 126 breakout board and am having no luck , wondering if anyone here has done similiar and can offer advice . i...
hi , i was wondering if anyone here has used mach 3 and a pmdx 126 breakout board with panasonic minas servo drives and motors , im retrofitting a waterjet machine and im having problems with wiring...
im looking for the ballscrew and not for an old style eztrak with cantilever arm quill drive . checking to see of anyone had upgraded to the newer style quill drive ,
thanks
robert brintle
thanks for reply , my machine has panasonic servos and drives for all 3 axis , it is a 3 axis machine but z moves down to programmed position , then x and y travel , at end of cut z moves back up...
hi , anyone ever retrofitted an older waterjetpro machine using the camsoft syatem ? i have an old higerman control that has become very troublesome and hard to find parts for. the camsoft system...
hi , i am in need of a copy of the eztrak operating software , i have been running version 5.00.21.08 on my machine ,. but my machine had a problem and lost it and my backup copy is corrupted ....
hi , i still use 3.5" floppys and still use them to load programs on my machine.
thanks
r brintle
hi , i am in need of a copy of the eztrak operating software , i have been running version 5.00.21.08 on my machine ,. but my machine had a problem and lost it and my backup copy is corrupted ....
hi , anyone have a good used directdrive waterjet pump they are looking to get rid of , im wanting to upgrade from my cougar 2 pump , but cant justify buying a new or even used intensifier pump right...
i have a pressure problem with a cougar 2 pump . it builds 40000 until i turn cutting head on , then it drops and holds 30000 . i have new diamond orofice , serviced check valves , and dynamic seals....
hi ,i need some help programming an eztrak to mill an arc in the xz direction, im trying to mill a 3"radius 3" deep in a block of D2 USING A .6875 ball endmill , i can get it to travel with radius...
hi , here are the files im having trouble with .185582185584185586