Search:

Looking for setting 163 on two older mills. I can't seem to find it, was it under another setting back then?

We have a 1993 VF2, the 0.1 Jog is currently disabled. which I want. We have a 1999...

We have an old VF2, 1992 vintage.

The "OFFSET" button on the keypad has stopped working properly. Sometimes if you press it just right and with just the right amount of (hard) pressure, it will...

Hey
Thanks for the reply. I was able to get a photo of the electrical cabinet and saw the 4th drive inside, and took the gamble. It indeed was 4th axis ready.
Would love to see the brochure on...

Thanks gwood. The Kilroy Corp helped me out with the plug. Sending the drive to them for repair.
Cheers.

I'm looking to remove the ServostarCD drive for my 4th axis. I can remove all the wires/plugs without any issues, except for plug on C4 port (Encoder Equivalent Output). This plug goes to plug J5 on...

Hello
I'm looking at buying a 1993 VF-2 from an auction for a good price. It does has 4th axis drive and wiring, but no 4th axis. Would this machine come with the drive/wiring if it did not have the...

Thank you!

Spindle drive.

Can anyone tell me what this means? I've searched and searched and can only come up with AL-## display readings for specific alarms. My drive simply reads "A".

A06B-6055 spindle drive.

Thanks

I replaced the X axis pulse coder on my mill. The part number is A860-0304-T111. When I try to move the axis even 0.001 the motor rapids abruptly and the machine goes into an emergency stop state and...

Here you go, from a 1998 Arrow 1000

389708

The old girl was working fine one day and wouldn't turn on the next day. Anyone have any idea where to start? Re-seated all connectors and checked all fuses etc and all seems fine. It did finally...

I agree. The few trouble areas with these machines is no reason to be worried about replacing the entire control. Once you are familiar with the control, these machines are great to work with. Clone...

This is how they were all made. Make sure when you load tools in the carrousel that the dimple on the side of the toolholder is opposite the drive key on the spindle.

Under normal conditions it's...

Thanks for all this. I will give it a go

I will be using a 25p to 9p converter to go to my USB serial 9p adapter. This wiring configuration should still be ok with my setup?


Sent from my...

What is wrong with your pendant? They can be found on eBay for around $1300 usually. And you can also still order some parts for them


Sent from my iPhone using Tapatalk

I got a tester and tried to punch a program. No lights came on at all.

I checked all the parameters that relate to RS232 and they are set to what that website was showing.

I don't know what...

Ok so it looks like the serial port on the machine is in face for a tape puncher.... Any way to confirm for sure that this machine does not have RS232 program transfer capability?

227872

Thanks!

Any tips on how to initiate the program transfer to the machine? :) this control is new to me and my documentation is minimal.


Sent from my iPhone using Tapatalk

Anybody have the wiring diagram to make up a cable for this machine/control? The machine has a 25pin female port on it inside the tape reader.

Thanks!


Sent from my iPhone using Tapatalk

Ok looks like the X axis actually is binding up. Removed the belt and the motor runs fine by itself but cannot turn ball screw by hand. Time to get dirty


Sent from my iPhone using Tapatalk

No I didn't. Not quite sure what to look for?

Is it on the end of of the servo itself?


Sent from my iPhone using Tapatalk

1980 TL-5 with Fanuc 6T (no CRT)

Machine was running great and alarmed out #401 during a light facing cut. Since then it will let me move X various distances before alarming out again. Everything...

No luck on that solving my problem. The brushes were about 5/8" long and a little carbon came out but not much. Off to the Mori Seiki forum to dig a little deeper


Sent from my iPhone using...

Does anyone have a quick rundown of how to clean the brushes on a Fanuc DC servomotor? I assume they are underneath the round caps that are in the middle of the motor?

Im having some strange 401...

Here are the part numbers. The feed and speed pots are on a single board so you only need to order one of them. The rubberized knobs are sold separately. I'm still waiting for my price quote to...

I can send you parameters. What is your email address

Ive bought these from MAG in the past. Digikey and similar places wanted a fortune for them. I actually just sent an inquiry to MAG today to purchase a couple of these for my machine. I'll be happy...

On your pendant, select Setup, Rem Axis, and disable the 4th axis. This should solve the problem

What is your procedure for aligning the machine?

Reference marks must be lined up beforehand, then hold the home buttong and Z,X,Y will align. Once the axis stop moving you can release the home...