510,012 active members
3,988 visitors online
Register for free
Login

Search:

Type: Posts; User: mactec54

Page 1 of 20 1 2 3 4

Search: Search took 0.03 seconds; generated 57 minute(s) ago.

  1. Re: Harvey / Helical putting mills down for 8 days and counting

    Can you not rough mill and bore it to finish size if it is a round bore
  2. Re: Need some general advice on VFD parameters for a spindle

    Yes that is the correct way to get a drive like this going to use the KeyPad first and then go remote, you don't need that type of switch button control you can do it all through your control...
  3. Re: Need some general advice on VFD parameters for a spindle

    You can not use a normal meter to measure the output Power of the VFD Drive

    You have to use all 4 Pins the spindle must be Grounded this sounds like another problem you have

    The normal...
  4. Re: Diving Head First... Huanyang 220v VFD + Water Cooled Spindle Upgrade on my G540/

    If everyone did it a build like this there would be very few problems
  5. Replies
    6
    Views
    16

    Re: Bosch Router on 2’x4’ Standard...?

    For feeds you are in control of that part you can adjust to suit what suits spindle performance
  6. Replies
    0
    Views
    7

    Re: Yaskawa Varispeed 626VM3 Fault A00

    Sounds like you may have a main Capacitor problem, the main Capacitors are not charging up correctly
  7. Re: Need some general advice on VFD parameters for a spindle

    It sounds like the VFD Drive is not suited for your spindle, but also may be something simple

    After you do a reset just put in all the motor spec's and what the Keypad needs the Minimum and Max...
  8. Replies
    9
    Views
    6

    Re: crane style cnc machine

    Yes that would be a problem for plasma I did not read enough of his post to see Plasma

    Works well for a wood / plastic router and for laser engraving
  9. Replies
    6
    Views
    12

    Re: Linear Rail Mounting Flatness

    Correct in most cases they are in tolerance, if you are looking for perfect then you match grind them
  10. Re: Need some general advice on VFD parameters for a spindle

    Yes there can be problems when changing settings as they have to relate to other Parameters that are already set we could change that profile

    Don't know what is going on the V/H ratio is .55 so...
  11. Re: Need some general advice on VFD parameters for a spindle

    Do you have 00-06=1 set for Pot control
  12. Re: Need some general advice on VFD parameters for a spindle

    You got a little messed up with your Parameters

    01-04=Default you should not be using this Parameter this is for the use of a second motor
    01-05=Default you should not be using this Parameter,...
  13. Re: Need some general advice on VFD parameters for a spindle

    You are figuring it out very well, as I said in the post yesterday there where other Parameters to change the 01-00=7 was the one to change
  14. Replies
    6
    Views
    12

    Re: Linear Rail Mounting Flatness

    Height of the Rails is unimportant it's the overall height of the Bearings that is important when installed, I usually match Grind the top of the Bearings if there is a mismatch more than the Bearing...
  15. Replies
    6
    Views
    12

    Re: Linear Rail Mounting Flatness

    Yes a good quality Mill can machine the required flatness needed for mounting linear rails deburring and stoning is all that is needed after machining, yes you can Grind and scrap them also, this...
  16. Replies
    9
    Views
    6

    Re: crane style cnc machine

    If you have a floor area problem you can build mount a normal 3 axes machine on the wall or free standing against the wall
  17. Re: Custom made gear knobs with BMW logo for resale?

    If you have an agreement with the auto manufacture to make aftermarket parts with there logo on it you would be fine just get it in writing as for using bone for inlay would not be a problem also...
  18. Re: Need some general advice on VFD parameters for a spindle

    Yes 02-03= 24,000 I typed the wrong number

    Don't be a alarmed if some of these Parameters can not be input, there is another Parameter to change if this happens

    Yes there will be more to set...
  19. Re: Break HF spindle with breaking resistor?

    There is a new VFD listed everyday I would say you don't have the Braking Parameters setup correct the normal without a Braking Resistor is around 3 to 5 sec for that spindle

    So your spindle is 4...
  20. Re: Harvey / Helical putting mills down for 8 days and counting

    If it is a Harvey Tool why are you not buying direct Harvey is a good company and shipping is same day as you order from them
  21. Re: Need some general advice on VFD parameters for a spindle

    This is a starting list there will be others to change

    TD 200
    .8Kw 3A Spindle 24,000 RPM 400Hz

    00.8=400

    00.11=133.4 ( ?? or 20 )

    00.12=400
  22. Re: Thanks for the Thread!! Made my decision on which company. NOT FLA...

    Thanks for the feed back Micknm Gary, I only use Ac servos, and have used them for the last 20 years I get a very good price break for using Ac Servos which would cost around the same as any quality...
  23. Re: Break HF spindle with breaking resistor?

    What VFD Drive do you have
  24. Re: Putting urethane pads under leveling feet (mini mill 2)

    Concrete will absorb most vibrations that you will get from either of these 2 machines

    I don't believe it would be a good idea I had a CNC Bridgeport on urethane pads and it would move around...
  25. Re: Thanks for the Thread!! Made my decision on which company. NOT FLA...

    Thanks Gary I will start a thread but may not be able to reply to it as often as needed so will get lost in the jungle I posted here just testing if there was any interest
Results 1 to 25 of 500
Page 1 of 20 1 2 3 4