510,008 active members
3,837 visitors online
Register for free
Login

Search:

Type: Posts; User: Leelund

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    5
    Views
    345

    Sounds like instead of a tech you should have...

    Sounds like instead of a tech you should have called a preist for an exorcist.
  2. Replies
    7
    Views
    672

    Here is the page out of the manual158213

    Here is the page out of the manual158213
  3. Replies
    7
    Views
    672

    Hi Mike, I was adding info to my original post...

    Hi Mike,
    I was adding info to my original post when you posted the picture. I found a 5F alarm in the MDS manual. It mentions the external contactor being welded. I guess anything along those...
  4. Replies
    7
    Views
    672

    Hello Mike, I don't have a listing of a 5F...

    Hello Mike,
    I don't have a listing of a 5F alarm either. If you look in your electrical cabinet the Z axis amp should be displaying an alarm code as well. What is the drive saying? What model is...
  5. Replies
    2
    Views
    890

    S Params

    S12-GRDSPC- The grid interval of your axis. Usually you can find this listed in your electrical manual that shows your motor and encoder wiring. It usually says the grid spacing.
    S23-VIL- Speed...
  6. We use individual mist collectors, smog hoggs,...

    We use individual mist collectors, smog hoggs, Torit, on our MC's. Coolant still gets in fans. We change/clean CNC filters every 2 weeks and they are black and slimey. Oilcooler filters- same...
  7. Replies
    2
    Views
    487

    Is it firing the open solenoid and trying to...

    Is it firing the open solenoid and trying to open? If so, it sounds like the linkage has is bound up. Turn off the air to the machine and try to manually pull the door open. With no air on it, it...
  8. Replies
    2
    Views
    871

    PLC parameters are listed in your electric...

    PLC parameters are listed in your electric manual. Pretty sure there is a description also.
  9. Replies
    1
    Views
    615

    Old ones were 12 volt bulbs. Base of the stack...

    Old ones were 12 volt bulbs. Base of the stack had a transformer in it. 120 ac in 12vdc out. New style are led light stacks. pretty neat. Probably pretty pricey from Mazak. Google "Patlite" and...
  10. I don't think there is both a limit switch and...

    I don't think there is both a limit switch and prox switch. It's probably one or the other. We no longer have the machine and I'm trying to remember 25 years back. I can't remember what type was...
  11. Let the fun begin!

    Go to the diagnosis interface page and see if H05 bit 3 turns to a 1 status when you shift to low gear. Make sure that H05 bit 2 goes to a 0 status also. Both should not be "on" at the same time. H05...
  12. U R on it Gridley! Especially if it says gear 0....

    U R on it Gridley! Especially if it says gear 0. Control doesn't know it finished the shift. Tweak the sensor a little. If you cannot get there, or have to move the switch a lot, then maybe the...
  13. Replies
    2
    Views
    596

    Unwire the motor from the drive and see if it...

    Unwire the motor from the drive and see if it powers up to the ready condition. 32 alarm with the motor leads unwired will mean drive is blown. Power transistors may be shot in the base of the drive....
  14. Replies
    1
    Views
    382

    Or here- http://www.omnivisionusa.com I have...

    Or here- http://www.omnivisionusa.com I have installed their retrofit in as little as 20 minutes. Maybe a bit pricey though. You will have to decide. My outfit has deep pockets.
  15. Did you change the battery with power on? If so,...

    Did you change the battery with power on? If so, did you try to recycle the power at the main disconnect, then power back up?
  16. Replies
    11
    Views
    2,817

    AIR! If I recall they had air chucks installed on...

    AIR! If I recall they had air chucks installed on them. Gotta have air on to the machine and the pressure switch made.
  17. Replies
    93
    Views
    5,982

    Left Field

    I may be way off base here but I think I recall something about a spindle zero speed output from the SX controller to the T1 controller before it will even try to shift.
  18. Replies
    1
    Views
    564

    The problem could be the encoder cable itself....

    The problem could be the encoder cable itself. One of the wires may have parted or broke. Check continuity from the honda end at FX06 through the cannon connector at the encoder.
    If the cable...
  19. Replies
    3
    Views
    668

    The TL LED on the MV4 is a tach loss. Led1 is a...

    The TL LED on the MV4 is a tach loss. Led1 is a direction command I think. You need to clear the tach loss by recycling the main power off/on. Check to see if the red tach loss alarm has cleared. If...
  20. Thread: MACHINE HOURS

    by Leelund
    Replies
    1
    Views
    365

    Diagnosis Key -> Hit the Window Button on the...

    Diagnosis Key -> Hit the Window Button on the lower righthand corner of the control -> Click on Accumulated Time. Same from the top where it says File Edit Window Help on the top left corner of the...
  21. Replies
    2
    Views
    413

    Not familiar with the Meldas 60, but you would...

    Not familiar with the Meldas 60, but you would think there would be a 2nd Home or Number 2 Zero position for Z axis. Should be a Machine Constant Parameter that probably is listed in the Machine...
  22. Replies
    8
    Views
    1,681

    You're on it nlh! Don't you have to release the...

    You're on it nlh! Don't you have to release the reset but keep the OT release in while you jog it off the hard limit? And if I remember right, if it's a VQC type, and Y is over in the ATC area it has...
  23. Our Mazatrol Matrix and 640 Pro's all have the...

    Our Mazatrol Matrix and 640 Pro's all have the next tool ready and waiting in the atc arm and the spindle tool magazine pocket called up ready foe the return after the exchange. Maybe a Fanuc thing?
  24. Replies
    3
    Views
    1,338

    Onboard batteries on 442, 471 or 472 or 474 if...

    Onboard batteries on 442, 471 or 472 or 474 if so equipped. 3.6 Coin cell in O62 battery box under the 721 drive.I think you should have three 3.6 coin cells and the 6 volt sealed lead acid total.
  25. Replies
    2
    Views
    568

    Machine parameter M1 is rapid feedrate.

    Machine parameter M1 is rapid feedrate.
Results 1 to 25 of 150
Page 1 of 6 1 2 3 4