hello do you have a post for acramatic a2100 milling that you could send me please.
regards
mallardfizz
Type: Posts; User: mallardfizz
hello do you have a post for acramatic a2100 milling that you could send me please.
regards
mallardfizz
hello the symptoms you describe would suggest the problem is with the power supply not the
spindle drive. i would recommend you test the psu before sending the spindle drive away.
regards...
hello again
if you send an e-mail to my e-mail address i will send you a copy of the electrical drawings and try to give you some fault finding instructions
[email protected]
regards...
hello
what electrical schematics is the machine wired to?
you will find the number on the silver label on the outside of the electrical
cabinet door. it is the bottom number and starts 9120****...
Hello
my e-mail address has changed to [email protected]. send me an e-mail with details of what you want.
regards
mallardfizz
hello
this machine was built in 1994. it is a Fanuc OM control.
regards
mallardfizz
lo interested to know who you bought the resolver from and approx cost.
as to your other thread i think you might have trouble getting to the bottom bearing to remove excess grease. i have replaced...
hello again
experience would suggest the flat screen is the problem. i have changed several lcd screens but only one scsi board - and that was because the screen would 'flicker' there was still an...
hello
if you have an lcd screen then you either have a later motherboard which has the 50 pin scsi screen connection at the front OR most likely you have an earlier motherboard with a 15 pin...
hello
does this happen when the table is at its rear position (nearest to the column)? if it is then one possible cause is swarf trapped behind the saddle.
on early machines the table aligns at the...
hello if you send me the software details from both of your machines i'll try to help. please send it via my e-mail [email protected]
you will find the details by
pressing MORE
pressing...
hello drop me a message on my e-mail address - [email protected] - and i'll send my phone number to discuss your problems.
regards
Dick
(mallardfizz)
hello
i dont believe in coincedence so i think the hard drive could be the problem.
is there an A4 folder with the machine? it is usually kept in the electrical cabinet and contains a floppy with...
yes you call me on that number.
regards
Dick
(mallardfizz)
hello
i think the flash card replaced the original hard drive (probably by me). i think you might need a replacement or the software reloading.
regards
mallardfizz
hello again.
just a thought. after pressing the Mech Jog button try pressing 'MORE' on the pendant. also if you press any other one of the buttons with the white background then press 'Escape' then...
ps
what is the schematic drawing number the machine is wired to? its the bottom number on the silver plate on the outside of the cabinet door.
regards
mallardfizz
hello
please be more specific. which button are you pressing for mech jog?
what does the display on the pendant show when the 'mech jog' button is pressed?
regards
mallardfizz
since the previous post couldnt be bothered to reply i'll repeat the question
WHAT BUTTONS ARE ACTIVE ON THE PENDANT?
If you were to drill a grid of 100 holes and the drill broke half way thru then...
hello what is the alert number on the alert shown in the picture?
if it is 4000F then try swapping the DV5 Boards between the two machines.
the DV5 is the board with the 5 silver plugs on the...
hello
look at the pendant. what leds are on?
regards
mallardfizz
hello Paneltec.
send an e-mail to [email protected] with a phone number and i'll talk you thru the align fix
regards
mallardfizz
hello again
i thought i replied that you can run with a keyboard and mouse plugged into the top of the control. have you looked at what speed is being seen by the control on the servo setup page?
hello
the battery on the workstation board needs replacing. the old battery has failed and the board has reset to factory settings. it would appear that your machine has an lcd screen and there are...
hello
instead of closing the doors try giving the guards or the table a good thump. it could be the 'heavy' closing of the doors is shaking something loose. what electrical diagram is your machine...
Hello Greg
it's been a long while since i programmed but try this
at the start of the program put in a 'count'
ie :g0t1m6
[#count]=0
[here]
program
"
"
"
hello
what schematic drawing is your machine wired to?
youll find the number on the silver label on the outside of the electrical cabinet - it starts 9120****.
regards
Mallardfizz
hello
press MORE
press SYSTEM CONFIGURATION
press SECURITY
type in SERVICE
press enter and commit changes
regards
Dick
(mallardfizz)
Hello
NO. the alert is only for the a2100 power supply. is the new one an AT psu or an ATX? If its an ATX then you will need an adaptor for it.
regards
mallardfizz
PS if Larry from Patriot is out...
have you installed the option code number?