Search:

I am going for a blunt start on a 2/78 -8 acme. I use the G76 for the threading and blunt start. I'm %99 there but I want a faster pull out to get a more "blunt thread. I have slowed the RPM down...

Why doesn't this G92 not work? Fanuc Series 2iTB controller.

I'm thinking a thread parameter change.

it gets here

G0 G54 X3.071 Z.2 M8

Then it just goes home.

Bought a used Mighty Viper with an older Fanuc controller. (2007) Its an OT XXX or other. I have most of the parameters and settings dialed in. Probe arm works and I'm getting good geometry...

I have tried everything under the sun to get this Dyna controller to talk to a PC. I use DNC4U. Works great for my Haas. I know the DNC4U is in contact with the controller because it is receiving...

After doing some research this won't do what I want. This will provide storage, but that's not my problem. It's program size and this emulator will give me what I already have. About 1.44 worth of...

RS232C is the only way I can run from the floppy. It's not dedicated on the 40 controller at least as far as I know. It's only 30 bucks, guess I'll give it a try.

Phoodieman

I wonder if this would solve my memory problems on the Dyna 40. Stay in RS232C mode and run from the emulator/usb stick.


Amazon.com: SFR1M44-U USB Floppy Drive Emulator for Industrial Control...

I tried that exact pin out. I bought DNC4U to manage my machines and with that pin out all the parameters are working except CTS so that isn't the right one as far as I can tell. In one scenario I...

I have a 40M controller that I'm trying to talk to a PC with. Between the manual, on line sources, and everywhere else I have two or three different ways to wire the cable. Does some body actually...

I am trying to make 1/2" spot faces on the fin side of some heat sinks. The fin is 1" high. How do you get through the fin and to the base without wrapping the fins? I have 24 units with 20 spot...

DNC4U has a wizard that you run to help set up the parameters for each particular machine. I must be getting some kind of connection because it's saying there is data coming from the machine, but...

The RS232 port on this Lagun is at the back of the machine, so if I want to bypass this port, do I go inside the controller to get to it? (The box with the keyboard on it).

Phoodieman

There is shop across town that has a Tree mill with the exact same Dyna controller. He drip feeds to it all the time. The only difference is he uses the printer port set up on one end and the DB9...

I have DB9 on a Dyna 40 controller and I have tried every pin out I could find. The only communication I have gotten was a series of "1"'s and "0"'s. and that was in transmit mode to the PC. I dnc...

I tried all the sources I could find for a 200 Series Master Holder. No one has one. One place said they were tooled up to make them, but it was a 3 or 4 month lead time. I'm going to make my own....

That would be it. Thanks. Thing must be heavily gold plated. $690.00 US....Might try Ebay.

I picked up a big box of kwik switch tool holders. It didn't come with the master holder. Not a problem as I found several. I only have Cat 5 in the shop. (Besides an old dinosaur Bridgeport). I...

Machine parameters are linked with the serial number of the machine. The tech at the local HFO e mailed the ones for my 2002 no problem.

Phoodieman

Thanks for the tip. It worked!!!! I can read the screen a lot better. That will at least put off another purchase for a while. There was a hole on the side, but it didn't lead to the pot. After...

2002 VF3 with an amber monitor starting to get where I can't read it. Is there a constrast button or setting so I can get a little more life out of this thing until I have to replace it. And then,...

I have a Dyna 40 controller on a Lagunmatic 3516. Tool change has become hit or miss. (Mostly miss). The spindle will spin to orientate, hit its mark then turn very slowly. If it does that the...

The HFO rep was at the shop and he said the door interlock was a liability issue. He said overseas it was a big issue to disable the interlock. (That's what he told me). I figured he knew what he...

Machine is a Haas VF3 with auto pallet system. Both pallets are on the outside table. M50 won't load either one. What do you have to do to get a table on deck.

Phoodieman

I see what you are saying and yes he's right

# Post Name : MPCENM4
# Product : MILL
# Machine Name : CENTROID
# Control Name : M-SERIES
# Description ...

m=mill, cen=Centroid, 4=4 I know this isn't right.

MPCEN4 is the post I have and it works for a 3 axis horizontal mill with a 400 controller. Which is what I'm running.

So the call out...

Looks like I stumped the forum.

Phoodieman

I have a Centroid mill and lathe controller. I thought the MCEN4 was a post for lathe and mill. I get good code for the mill. (I had to change 73 to 83 in the post to get deep hole drilling to...

I bought the ladder for the Puma 8S from Daewoo.

Phoodieman

The version is 8.0, but that's not the problem. It's a 3D part and I've been able to do anything with a lot of other parts that I wanted to. The part is there I just can't select anything. I'm...

I have a good drawing and can see everything in wireframe and solid mode. I can't pick anything though. What button or setting to I have to change?

Phoodieman