I am looking to buy a new to me cnc mill this is not my first purchase but will be the first time to consider a kitamura heard OK things about them from other machinist through the years but no first...
Type: Posts; User: msherman
I am looking to buy a new to me cnc mill this is not my first purchase but will be the first time to consider a kitamura heard OK things about them from other machinist through the years but no first...
I can move my 4th axis with m15 and m16 but i can not put in a feed rate?
It will only move at rapid I need to make a spiral cut how can I feed my fouth axis with the tool engage in material?
...
I NEED 2 POST PROCESSORS MADE BOTH FOR OKUMA
ONE IS FOR OSP 5000L-G 2X LATHE
SECOND IS 5000M 4TH AXIS MILL
MASTER VERSION 9
IF YOU HAVE THEM AND WANT TO SELL OR GIVE THEM TO MEI AM OPEN TO ALL...
OK I ADDED PICS FINALLY
SO WHERE WOULD YOUR CODE FIT IN ?
ONE PIC OF THE CODE AND ONE PIC OF THE GROOVE AS YOU CAN SEE IT WANTS TO EXIT RIGHT THRU THE PART
395108
395110
ok i know what they stand for just not the order no reason to have g91 and g90 on the same line
trying to get some pics
It might help if i understood what you r programming there
so if i for go the g85 lap cycle or is that added in to the g85 lap cycle where does that code fit in
also not sure of the three gcodes...
i need to exit out at a 30 degree angle it told me m85 is unrecognized so i must not have this option
i will probably have to go at it with out the lap canned cycle and just program it line by line...
i am programming a deep grove that is at a angle.
my problem is when it is finished roughing it exit out through the part.
how can i control the exit from the canned cycle and i am not using the...
chuck clamp light takes almost 5 seconds to come on and allow me to push the cycle start button
this is a new to me machine i am sure it is on some kind of timer i just dont know which parameters...
have a probable board issue which is way over my head need someone with okuma lb15 knowledge to help fix.
zip code 75751 which is in east texas near tyler
thanks
I need to replace this item i can not get a part number and so far hartwig has been no help.
does any body have any info that can help
osp 5000l-g control
Ok thanks yes that worked i was just timid on changing parameters but that is more like a setting
I just bought this machine it run fine the z axis stop 6 inches short of the chuck.
I am sure it is a parameter issue need help finding the right one.
any help will be greatly appreciated thanks
what controller r u using lets start there
i will suggest sending out to brett malberg forgot his user name on here
this is his email address [email protected] i had the same issue and final sent it to him fixed it fast and very reasonable
Is there anybody with experience in this matter maybe there is already a thread about this that i over looked
would be happy if somebody would point me in the right direction thanks
I have a mutliple part setup i am woking on and i am having trouble getting my machine to read my h word for second setup
i have multi setup on my experince in a multi setup on this machine is none...
greg b i was able to clear just by turning off and back on and it has went away and not pooped up again if it does then i will start to check
and diagnose the issue i was just wnadering if anybody...
just trying to boot up i am learning that about this machine
if you turn it off and back on that seems to clear the issue
so i am still operational juat wanted to learn more it incase it comes...
ok who has seen this message before
http://i1194.photobucket.com/albums/aa370/msherman26/20130212_160519_zps408078e2.jpg
and if so what did you do about any sugeestion aill be appreciated...
I am having a x axis issue we think it might be just the bearing but unsure
we get a lot of feed back i.e. high pitch ringing sound from motor when the table is moving but it only happens when the...
OK COOL I HAVE SENT YOU A EMAIL WITH THE BIOS INFO
LET ME IF U GOT IT
OK THE WHITE SLOT IS WHERE THE VIDEO CARD WILL HOOK UP
AT LEAST THAT IS WHAT I HAVE BEEN THINKING
I CAN SEND U A EMAIL OF THE BIOS FOR MY WORK STATION BOARD
AND MY RT BOARD I GOT BOTH FROM THEM
I CALLED SIEMIENS AND THEY SAID I CAN PUT IT BACK IN AND HE SENT ME A COPY OF THE BIOS THAT I NEEDED TO PUT IN
NOT JUST ANY OLD CARD WILL DO AND THAT IS MY PROBLEM
FINDING ONE THAT WILL FIT HAS...
YES I AM TRYING TO CHECK TO SEE IF I LOST BIOS'
AND IF I DID GO AHEAD AND PUT IT BACK IN
MACHINE SAT FOR A LONG TIME AND BATTERY WENT DOWN ON IT '
AND NOW I NEED TO SEE IF BIOS WAS LOST WHICH I...
I HAVE CINCINNATI ARROW 1250
I HAVE NOT TRIED THEM YET
I JUST TRIES SOME VIDEO CARDS WE HAVE
LAYING AROUND IN SOME OLD COMPUTERS
HERE AT THE SHOP
WOULD THEY BE ABLE TO TELL NE WHICH ONE FITS...
http://i1194.photobucket.com/albums/aa370/msherman26/20130117_142615_zps2e839463.jpg
http://i1194.photobucket.com/albums/aa370/msherman26/20130117_142708_zps6f906f96.jpg
I am need of a video card for my rt board
pn is 3-424-2169a03 i am having a hard time finding one
does anyone have any recommendations
i can take pics of it if that helps
thank in advance mike