501,588 active members
5,298 visitors online
Register for free
Login

Search:

Type: Posts; User: positiverake

Page 1 of 9 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    40

    Re: Milltronics ramping

    Nothing? ok how about this, does anybody know were the spindle bearing purge drain hole is and how to check if its working?
  2. Replies
    1
    Views
    40

    Milltronics ramping

    Hello, this is a 2003 vm25 with Milltronics Centurion 7 control, when I use the clear pocket for a slot and tell it to ramp for Z it does a helical circle at the Z depth of cut? and if I change the...
  3. Tool changer recovery VM25 7 control

    Anybody have a tool changer recovery procedure for a 2003 VM25 side mount 24 tool ATC ? seen my boss use a ratchet on the top of the ATC and crank it until the proximity switch's came on, just...
  4. Replies
    35
    Views
    226

    Re: Rigid tapping toolholder

    420716 This is what I use, it uses quick change tap holders and does have a little movement but is Rigid, works great
  5. Replies
    3
    Views
    57

    Re: 2003 vm25 7 control

    Yes the parameter 90 degree cutter comp works
  6. Replies
    3
    Views
    57

    Re: 2003 vm25 7 control

    Thanks for the reply, yes I do have a lead in, I program it to come in at a perpendicular line to pick up the comp and the control moves in X and Y
    I did see a parameter in my fast cam2 that...
  7. Replies
    3
    Views
    57

    2003 vm25 7 control

    How come when I use cutter comp this machine comes in at a angle even when I program it to come in 90 deg (perp) ? parameter? Thanks
  8. Replies
    6
    Views
    188

    Re: Miltronics VM 25 with 7 control

    sportybob, I must not be explaining what I'm trying to do very well, I will give you a call. thanks
  9. Replies
    6
    Views
    188

    Re: Miltronics VM 25 with 7 control

    Yes I have that turned on and I am using a touch off block, I guess I will just make sure that all my Z numbers in the work coords are zero when setting tools and Z work coords or do like someone on...
  10. Replies
    6
    Views
    188

    Re: Miltronics VM 25 with 7 control

    Sportybob, yes Im using the RUN, TL set program, Im trying to get the machine not to use the z offset in the G5x in the tool H offsets. I'll take a look. thanks for the tips.
  11. Replies
    6
    Views
    188

    Miltronics VM 25 with 7 control

    VM 25 Miltronics 7 control, Hello, some of the user parameters (0-99) on the machine I run have numbers in them, should I worry about this or use them anyway? there is only one guy that ran this...
  12. Replies
    12
    Views
    439

    Re: Centurion 7

    Very cool!
  13. Re: Fanuc T21i, Wear Offset affects Absolute readout, can I change this?

    See attachment and look at page 643, this is Fanuc Oi MC but should be the same for what your looking for
  14. Replies
    12
    Views
    439

    Re: Centurion 7

    Hi sportybob, yeah it has some cool stuff, like I said its a 2003 model, I'm sure the new ones are even better, I'm getting use to the control, seems like out of the gate they were geared to be in...
  15. Re: Fanuc T21i, Wear Offset affects Absolute readout, can I change this?

    Do you have a parameter book for the Oi ?
  16. Replies
    12
    Views
    439

    Re: Centurion 7

    sportybob, yes it seems like they are getting better and better, I do like the fact that the new machines have more switches on the control panel so you don't have to go through a bunch of screens to...
  17. Replies
    12
    Views
    439

    Re: Centurion 7

    Thanks for the reply, yes that is the only place I have seen them and that's only after you set a work coordinate, I want to see a page that shows the G53 position anywhere I move the machine and...
  18. Replies
    12
    Views
    439

    Re: Centurion 7

    Thanks for the reply sportybob, I just found the screen parameter today, didn't seem like it worked, you must have to power down? I guess I'll find out in the morning. I know what the G53 is but...
  19. Re: Fanuc T21i, Wear Offset affects Absolute readout, can I change this?

    Take a look at parameter # 3104 bit 6 (DAL) should be set to 1 this is for the absolute position, let me know if that is what your looking for.
  20. Re: Fanuc T21i, Wear Offset affects Absolute readout, can I change this?

    Yes there is parameter for this, I dont have the book in front of me but I have changed it in the past, like you I hate that, I want to see the programed number not the offset, if you got a...
  21. Replies
    12
    Views
    439

    Centurion 7

    Hello, is there a way to see the G53 machine scale position on the screen? Machine is a milltronics vm25 with a Centurion 7, 2003 year, also how about a timer that shuts off the screen at Idle? ...
  22. Thread: Fastcam2

    by positiverake
    Replies
    5
    Views
    241

    Re: Fastcam2

    pm sent, thanks
  23. Thread: Fastcam2

    by positiverake
    Replies
    5
    Views
    241

    Re: Fastcam2

    No just the c: prompt
  24. Thread: Fastcam2

    by positiverake
    Replies
    5
    Views
    241

    Fastcam2

    Hello, I have milltronics fastcam 2 version 6.6206p that im trying to run on a windows xp so I can use it at home, cant get it to run, i can get both 3.5 disc in and it says its installed and to type...
  25. Replies
    14
    Views
    3,753

    I know this is really old but would like to use...

    I know this is really old but would like to use the simulator, Im getting error (pfile.dat has been corrupted)I dont have a copy of the pfile.dat from the machine. can I get around it somehow with...
Results 1 to 25 of 206
Page 1 of 9 1 2 3 4