501,588 active members
5,291 visitors online
Register for free
Login

Search:

Type: Posts; User: christian7r

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    69

    Re: help with torq cut 22

    https://www.cnczone.com/forums/attachment.php?attachmentid=420230&stc=1https://www.cnczone.com/forums/attachment.php?attachmentid=420232&stc=1
    that's the voltages that he gave me when I measured...
  2. Replies
    4
    Views
    69

    Re: help with torq cut 22

    ok I will check all the voltages right now the two transformers are set to 230v

    Thanks
  3. Replies
    4
    Views
    69

    Re: help with torq cut 22

    https://www.cnczone.com/forums/attachment.php?attachmentid=420120&stc=1https://www.cnczone.com/forums/attachment.php?attachmentid=420122&stc=1
  4. Replies
    4
    Views
    69

    help with torq cut 22

    hi months ago I bought a torq cut 22 and this week I connect it and when I give it to enable the drives they activate the contactors and they are deactivated and I get the axis drive fault alarm,...
  5. Re: 1996 Bridgeport Torq-Cut 22 Voltage change

    I have not done it yet I asked if someone had done it.
    I saw one that I want to mount but I have a doubt the engine encoder is only for the RPM or it is also used for the position of the spinder...
  6. Re: 1996 Bridgeport Torq-Cut 22 Voltage change

    The vfd drive can be replaced by a universal one
  7. Replies
    0
    Views
    96

    question about vfd in torq cut 22

    I wonder someone has changed the vfd to a torq cut 22 for a universal one other than the yaskawa and another question that works does the encoder that is under the transmission
  8. Re: converter recommendation for torq cut 22

    ok thank
    I'm checking a step up transformer 208v to 480v
  9. Replies
    34
    Views
    2,577

    Re: The Broncobots Torq-Cut 22 Restoration

    A question like did to update the DOS and install the window is that I bought a Torq cut 22 a few months ago and I want to update it and make a backup on the hard drive and also buy a solid state...
  10. Re: converter recommendation for torq cut 22

    I did that without connecting the VFD and since everything turned on the spindle motor says on the 400v board, I read something that the axis drive faul alarm is because the vfd is off so it does...
  11. Re: converter recommendation for torq cut 22

    for the spindle and the VFD I will have to install a transformer 208 to 480v
  12. Re: converter recommendation for torq cut 22

    it's already on but I'm having a problem when I give the drive the enable it is giving me an alarm (Axis Drive Fault) that could be causing this failure

    Thanks
  13. Re: converter recommendation for torq cut 22

    greetings I could not answer but I'm back the voltage in my house is 230v and configure both transformers to 230v and I could turn on the electrical panel without turning on the VFD or the...
  14. Re: converter recommendation for torq cut 22

    Ok
    if it is something strange because the vfd is 230v and the spindle motor says 400v
    I think the single phase current is 240v I have to measure it to see how much it gives me

    the coolant pump...
  15. Re: converter recommendation for torq cut 22

    photo of the VFD and the spindle motor
  16. Re: converter recommendation for torq cut 22

    The VFD input is 200-220v/50hz 200-230v/60hz
    I'm trying to upload a photo but it will not let me try later
  17. Re: converter recommendation for torq cut 22

    not only do I have a small rotary phase that I use for the conversional milling
  18. converter recommendation for torq cut 22

    I acquired a torq cut 22 that was installed at 480v and where I am going to install it there is no 480v converter that I recommend or how I can install it to make it work

    thanks for your help
Results 1 to 18 of 18