I hope this is the right place to ask this question.
Can someone tell me several sites where I can order ball screws, side rails and things of that nature?
I want to extend the travel of my...
Type: Posts; User: Jamesdee
I hope this is the right place to ask this question.
Can someone tell me several sites where I can order ball screws, side rails and things of that nature?
I want to extend the travel of my...
Yes I was.
I hope this is the problem. I use a USB drive to copy my PLT files to the laptop in my shop to run my cnc. I thik I had a bad usb drive. Using a new one seemed to cure the problem . . . . . . . .I...
I hope I am explaining this correctly:
I have been using Planet CNC successfully for several years.
The last few months for whatever reason the job I am running will stop, the job screen will...
My MultiCam 22Plus was purchased in 1997. It worked great until the spindle broke. Being a cheapskate I purchased a Kress spindle after trying some lowball routers.
Like you, I was tired of using...
They are ball screws.
Sorry . . . . . I don't know. It's a MultiCam 22 Plus CNC router.
Howdy . . . . . .Can someone tell me the "BEST" lubricant to use on a screw drive? Also how many hours of use between cleaning and re-lubricating?
Never seen anything in writing.
Thanks in...
Did you get the MultiCam working?
I re-did my controller and software because like you my MultiCam was bought in 98. I built a Planet CNC controller and use Vertic "V-Carve Pro" software to design...
I have two Kress 800 FME spindles and am very happy with the Product. I would like to upgrade to the 1050 FME. They sell them for the Us and the specs say: 220 Volts input but the plug is the TWO...
Thanks, will give it a try.
Did you ever up grade? If so, to what?
Thanks for the reply. All three axis are off, X, Y, and Z. The picture of the connector block is not very clear but it is between the steppers and the old drivers. That is existing wire. I seen no...
In the process of upgrading my MultiCam 22 Plus controller to a Planet CNC 3/4 I have ran across a problem with the accuracy of the piece being routed,
First let me tell you what I did:
The...
Howdy from Grapevine, Texas.
I have a calibration problem I'm not sure how to handle.
I set-up my cnc router, "Arnold", according to Planet CNC instructions.
Needles to say when I do...
Glad the prints helped.
Progress is slow on the Planet CNC, MK3/4 controller upgrade. The problem I have at this time is I use "Arnold", my cnc's name, to carve plaques for various customers. So I...
I contacted Barney Robinson Hardwoods, Fort Worth. No luck, they do not have it.
Thanks for the attempt.
I make plaques and like to use Ash because of it's grain and staining properties.
I'm looking for Clear Ash, Grade One. 5/4 thick and 8 to 8 1/2" wide. Does anyone have a good source? I live in ...
Do you intend to sell the MT-22? What is the size of the table? I would be interested in using it for parts for mine.
Mine is "ARNOLD" as in the Terminator. When I first got the CNC the mechanical sounds it made reminded me of the movie. Even put vinyl letters on it with the name!
My MultiCam 22 Plus uses NEMA 23 Pacific Scientific Sigmax steppers. Can someone tell me what the driver setting is? I.E, 400, 800, etc., Steps per revolution. It is a 1.8 degree stepper which equals...
Looking for a used MultiCam 22 Plus. Does not have to be working.
I am looking for a "USED" MultiCam 22 Plus. Does not have to be working.
From experience I can tell you the Porter Cable is not the greatest. I burned out two of them. I am now using the Kress 800 and am very happy with it. Depending on what you plan on doing with your...
Howdy from Texas . . . . . . . . . Want to make money using your CNC router? Best if you make things that YOU are interested in. You are a bit limited in the size of your table but there are things...
268442
I hope the attachment came out.
I have made a few changes. I'm still using Windows XP & the DNC software to run "Arnold", (what I call my MultiCam). I use VCarve Pro to layout my work....
For years I have used Enroute which saved my files in the PLT format for my MultiCam CNC.
I am in the process of putting a new controller and associated gear in the CNC. Using the Vetric V-CarvePro...
Thank you. My limit switches are PNP 3-wire units, not the mechanical type. The optocoupler adapter are not built in the controller.
I am replacing my MultiCam 22Plus CNC controller and some of the other parts with a Planet CNC controller.
My proximity switches for the three axis will require an "optocoupler" between the limit...
Has anyone purchased the Kress 800 or 1050 auto tool changer spindle?
Looks like the price for the 1050 is about 599 Eu.
I have a Kress 850 and love it but would like to upgrade to the Auto Tool...