Search:

Thank you a lot. I got it :).

I mean after I added B axis and clicked "OK" then nothing changed on TNGv2. The interface just only have 4 axis (X, Y, Z, A). Did I skip any step?

Hi everyone,
After updating on TNGv2 I can't add more axis. I tried some time but nothing change. Could you give me an advice please? Thank a lot.

Thanks for your advice. I tried to dry it with compressed air even the dryer but nothing changed :((

Thanks Jerry, It's just only water and I haven't tried your way yet. I will give it a try.

Water overflow on the upper surface of the board. LIMIT, JOB and IN/OUTPUT ports were no longer seems to work correctly. What do you think about replacing the HC224 IC ? Thank you a lot.

Hi everyone, I have a problem with my mk3 controller board. All of it's input/output had noised after getting wet during operation.
This link below show exactly what going on with it. Can you give...

I'm using Torch height control for my 4 axis plasma tube and It worked greatly.

That's good idea. I will give it a try. Thank you so much David :).

Many thanks David, I'm using machine which I diy myself with cnckad V15 CAM software. It seems to be come from the controller, I guess. Because when I cut the same part in the cutting list. It worked...

Hi everyone, I have a issue with my plasma tube cutting cnc machine and I did'nt solve it yet. Could someone help me.
I tried to cut the tube 27mm dia with the thru hole 10mm in the face and the...

Hi Hung,
THC proma SD adjust the height by using the pul/dir from the CNC controller so you need a z axis so I think you should to use another controller which have Z axis or using the China THC...

Hi everyone,

I have a problem with my THC proma SD. It was not responded the G-code command from the interface software. I've already checked the wiring and tried simulation testting from THC...

Hi Shayne367
Try adjusting the SPE down mate. I'm using THC proma SD too :).

Hi everyone, I have a problem with my stepper motor configuration on TNG software, could someone please to help me?. Thanks a lot.
When I used the rotary axis for cutting the round tube by plasma,...

Hi everyone,
Now, I have a problem with my THC ( proma 150 SD) it always driver the torch contact with the material surface, I don't know why, I have already tried with another settings but it is...

Hi PlanetCNC,
In this clip ( please see picture below) where is the end of each wire of material probe switch ? If them connect with the controller how can I do it? Could you show me please? Thank...

Thank you a lot rodw,
I just need to connect the pin 12 & pin 14 on the hypertherm cpc port to the GDN& OK input pin ( config input pin 3) on the MK3 controller, right? ....

Thanks for your replies,
I have already checked and recongnized that a OK arc pin hadn't been connected, but I did'nt found the wiring diagram for a OK arc output with Cpmpact THC SD (proma) in...

Hi PlanetCNC,
I have already connected the THC (Proma SD) with plasma source (Hypertherm 45XP) dirrecty as your guide on the blog but the machine just only ran over the THC code line a little bit as...

I got it. Thanks you very much.

Hi everyone, I have a problem with THC G-code. When I uploaded the G-code in Planet TNG software and started to run it, the program just only ran a little bit and stopped at N51 line. I don't know...

The driver with adjustable current from 0.25-1.4A and it was supply 220V Voltage. You right! the motor seem to be overload even though I use gear box with 3:80 ratio. About losing steps on some axis...

Thanks you harryn,
About my A Axis rotary configuration:
+ Driver Vexta RKD514H-C set at 0.18 deg./step and 1.4A current.
+ Motor Vexta PK596 with 0.0144 deg./step resolution 1.4A current max and...

Hi BFS, you can use relay in the HY-JK02-M 5 cnc card to start/stop the plasma source.I have never used HY-JK02-M before but I had already saw it on the internet. Some link may be useful.
Wire JK02...

Hi everyone! I have a problem with my CNC controller setting ( I use Planet CNC USB Controller Mk3). My CNC machine have 4 axis ( X axis set axis 1 port,Y axis set axis 2 port ,Z axis set axis 3...

I got it, thanks you alot.

Hi everyone,
I'm An. Now, I have I problem with Planet CNC TNG software. I tried to activate THC Option in Planet CNC TNG but I did't find it anywhere. Could everyone please to let me know: "how to...

Hi guys, Could someone show me how to connect the hypertherm CNC cable to the MK3 please? Thanks a lot.