Sorry for the delay H ,
About your turret issues , The slam in my opinion can be caused by several reasons:
1-The shock absorbers , Does the turret slams in both directions ?
2- Not enough...
Type: Posts; User: cncatj
Sorry for the delay H ,
About your turret issues , The slam in my opinion can be caused by several reasons:
1-The shock absorbers , Does the turret slams in both directions ?
2- Not enough...
Things are quite good Here H !
It's good to hear that your machine is almost finished ,
I'm now taking a turret all apart !!
Puting all new Orings & seals
Hi H !
do you have this job done ?
Thank's guys , i send the board to be repaired by the experts
Hola Diego,
Recientemente vi un problema similar , entiendo que el puerto paralelo es de tu computadora cierto ?
Asegurate que la maquina es decir el chasis este aterrizado a la misma malla donde ...
MadMike :
On the W.station Board , I would not change the CR2032 battery until have all the bios settings writed down !
Hi guys , I have a Bridge board that needs a repair ,the problem is that it does not recognized the Floppy drive , already swap to other machine , & the problems goes with the PCB
I might be able...
skudzuki :
i probably did not explain clear enough , but you clearly undestand , Thank you !
The problem with this machine was that it lost parameters , some one else load it back
& for some...
Hi guys, hope that some one can help me out with this :
I am not able to align tool drum ,
I have been told that , because of this alarm, tool data tables need to be reset :
How can i enter...
Greg_
i would suggest that you remove spindle belts , and start spindle motor to a certain
desirable speed , so you can determine if the noise is in the spindle motor or not !
good luck
p.d...
How do your control looks like ?
post a picture...
Hi tony ,
i suspect that your VDC level is not at ther right level , you should read ,on my
oppinion at least 20 vDC !!
Hi ReBco.
The contactor that you refer , it actually feeds with 3 phase volt. to DC power supply wich gives the DC 350 VDC
As long as you have a software related problem or e-stop condition you...
Chaz :
is f this are the Vicker-Acramatic Blue servodrivers then :
according to a sheet i have here , P Display error means :
OverCurrent !! Possible Cause: Power stage surge current
Chaz,...
H. Sorry !! i'm the maintenance Tech. down here , you are not talking about a bar puller ? are you ?
The T. stock cylinder you should be able to actuate it just by air press,
with an air...
Hi H.
I have never seen any lube points in there !!
You will have to use some kind of a WD40 , & something else to remove all
signs of moisture from there ,
H.
The tailstock its a normal hydraulic cylinder ,
Hey , What if you swap hydraulics Directional valves ?
H.
Seems to me that, there is air in the Tailstock Lines !!!
I would take the air out by first adjust the T.stock pressure at low pSi. 80 or so ,
carefully lose a little , hydraulic...
HM , You are right , as soon as you press the button in the Lubrication unit , the lube pump should come on , IF you are not in the Auto mode ,
If pump does not come on , open the cover & make...
Hi Rolson,
Based on my own (Limited) experience with Cincinnatis
This problem could be caused by a stuck Z axis Motor brake , You can identifie the problem , Try to run only this machine ,...
H.
Glad to read your result ,
Another happy ending
Good luck !!
At this point , with the right phasing , no matter if E-stop board is wrong ,
like i told you , as long as you keep green power button at machine boot-up
you should be able to jog axis, rotate...
H.
The rotation on the hidraulic pump motor should be in the arrow directions,
if you go behind the machine you will se the hidraulics motor , with a pointing arrow on top
ours turn CW , if...
HMC I would first make sure the E-stop board is the problem !
Also, do you have wiring diagrams ?
HMc , check this also:
The crash sensor mounted on the base of the turret , is activated ?
is a plunger swithch
Normally it has not to be !!
so first of all make 100 percent sure it's not...
Also the 3 relays on that , A8 board are :
POTTER BRUMFIELD R10-EX6 - V430 24 VDC
hope this helps !!
Hi HMC , We have a machine like yousr down here, so here's my suggestions:
When this E-stop boards fails you can be sure if the power on the machine stays on as long as you keep pressed the...
Esmeralda :
Algo que hayas tocado probablemente y se desconecto ?
a veces pasa !!
si la maquina estaba trabajando perfectamente antes de que limpiaras el enfriamento,
Algo debiste haber...
Mike:
Any news ?
update ?
(alguna novedad ? )
Lefty1961
e-mail sent !