Did you Shutdown and restart after turning on comp?
Type: Posts; User: rl49
Did you Shutdown and restart after turning on comp?
Do you have this document
Hi Chris,
The C5 upgrade if you have enough processor power allows larger file run from memory I have done a bit over 4 MB files, I haven't any code larger than that to run.
To go to C6 you...
Congratulation's cbChris, google dos client networking and take it one step at a time as a dos network and newer windows can be very frustrating,
I have my piH with a c6 upgrade and a p1E cent5...
Hope this helps450876
Front panel lights are usually due to bad connection or power supply problems
Looks like your softkey.dat file in your C:\rom directory is corrupt.
Congratulation's, Good write up
No schematic but i do have a copy of this
Get an AT keyboard and plug into motherboard and hit Del key when boot screen comes up.
Ron
Do you have the original Hard Drive and the compact flash running?
If so does it boot off the cf?
It sounds like it cant find the atc macro or corrupt like you stated.
In the power parameter...
How about a picture and brand id?
Yes I had the original parameter sheet from factory and that will show you the areas you need to change when you have the 4th wired up.
To enable the axis you go into the power parameters and...
You just need to wire up a drive and get an appropriate encoder and set the parameters.
I did this on my Cent 5, do you have the schematics for your machine?
It will show you the wires you...
This from C6 programing manual page 158
Get to proteacted mode then
F9 (Shell) Main-Run-Displ-Shell
F9 (Shell) is available if the control is in access level 2 or greater. It will Shell out...
My P1H is serial # 2763, I am quite sure someone did the upgrade motherboard before I purchased it
My experience with a P1E 386Dx40 1993 era machine based control as the memory limitations are very limited, I have a P1H 1995 that had a 486 control and was also limited with the ridiculous ram...
post your code for the file you are drip feeding to see if that is the problem, I am assuming you use a cad cam app to generate the code? how big is it in megabytes? i
What mother board do you have is it a 486 or 386 from factory and how much ram does it have? Also what software version? send screen shots of this info and we can give you a possible solution.
Search:
Type: Posts; Keyword(s): 449, drive, fault; Forum = Milltronics and child forums
Buy an encoder from Milltronics the glued disk will not last especially if not centered. if you cant get the following error adjustment with the balance adjustment, you encoder OR wiring to encoder...
Was it this document?
I believe you have to purchase the probing option from milltronics, have you contacted them?
I haven't had to do many blind hole rigid tapping almost all my experience has been with thru hole, I would suggest to experiment with wax or aluminum to dial in parameters, also do search on rigid...
Might have ti use a propane torch or map gas to free up I purchased pulley to do same with my P1E but have the P1H which has rigid taping that works well and has 45 inch x travel so I haven't gone...
as a last check I would look at bios settings in motherboard to ensure its not fighting the C5 x card for control of com2 serial port. I have experienced issues with other dos based software mainly...
I would check the pulses at the P6 connector with your voltmeter to rule out ribbon cable issues.
On my P1H it has an CSM spindle and the PPU setting is different but it uses a resolver to...
2000, Sporty bob stated in this post https://www.cnczone.com/forums/milltronics/209846-get-actual-rpm-jive-commanded-rpm.html post #26 that fudge factor is only effective on C7 controls
Page 7 is same as my paper manual I purchased from Milltronics P1H by serial number but they sent me a non CSM spidle electrical paper manual.
From older posts in past I dont think a parameter...
I do believe you have to power off to take effect