Lathe od/id threads with g76 just fine also orients m19.
I have face drilled/tapped with c axis on and off X centerline g83 g84.
I have od drilled/tapped/milled with c axis on Z centerline (no Y...
Type: Posts; User: 64dodge
Lathe od/id threads with g76 just fine also orients m19.
I have face drilled/tapped with c axis on and off X centerline g83 g84.
I have od drilled/tapped/milled with c axis on Z centerline (no Y...
Yes I want to tap on X0 center line to free up
the only 1 horz live tool for polar coordinate milling
I tried it with and with out m29s?.
Straight g84 as you suggested Heavy-Metal.
Either...
It also has this in the M CODE list.
But doesnt work either.
M27 RIGID TAPPING FOR.(CW)
M28 RIGID TAPPING REV.(CCW)
M29 RIGID TAPPING MODE ON
This lathe was bought new last summer.
I started there in Oct. Have been asking boss
to call who they bought and get some answers
because it has other problems also.
That would suck if thats the way it is.
I went thru the programing manual and it has examples for main spindle tapping
and it didnt work either.
Thanks for the link, got some ideas for polar coord milling.
What I forgot to say was when it gets to the M29 line trying to tap
with main spindle it just stops and sits there with no error.
Machine has fanuc oi-tf control with c axis and live tooling.
I can get it to tap with horz & vert live tooling but not with main spindle.
Tried every thing I can think of. This works for horz on...
I think this machine is a samsung copy.
Thanks
Tim
Started a new job running a Smart Machine Tool NL 3000 BLM with Fanuc Oi-tf control.
Having trouble with M78 not releasing tailstock in program or mdi, M79 works the way
it should. In program it...
I had trouble with V8 on Win7 so now I use virtual box to run xp for Mastercam.
If its a one off and you are making it from plate or bar the right thickness.
1
Hold it @ 1/8 deep in vise drill holes a bolt size(3/8 for 3/8-16), pocket through part.
Profile to @ .01 top of...
Thanks A_Camera, I have been preoccupied with getting it back going.
I had inadvertently messed up the parameters while trying to get the vfd/spindle to work with Linuxcnc.
I was wondering if...
I also went through every parameter and wrote them down to have a backup.
I jumpered over so i could have spindle grounded.
Both bottom screws have ground symbol next to them.
383844
Thanks so much Mactec for the help!!!
Its alive again!!!
There were several parameters different from what you posted.
I went through and wrote down every one for future screw ups.
They...
The 2 screws marked ground below power terminal on the left & right in the housing arent connected to ground beside UVW.
Thanks Mactec for the info!!!
I found and downloaded the pdf manual it has a lot more technical detail about parameters than the paper manual that came with it.
The grounds were another thing I...
Ive been looking through the manual at parameters, had to find magnafying glass to read it.
You are correct about R &T for single phase. I will have to fix that. Hope that hasnt damaged anything.
...
It has about 25% anti freeze in water. It wasnt frozen, pump was flowing a good stream.
Water was really cold from the single digit low teens night time temps of the past week.
When I got in from...
How can you tell if vfd has rs485 componets.
Its a Huanyang 2.2kw 220v HY02D223B.
The screw terminals have rs+ rs- connections.
Tim
I bought a 2.2kw inverter & water cooled spindle off e bay ( supposed to be true huanyang from loveshoppingjxts ).
Set it up with correct settings, its worked great the last few months. I turn it on...
I get at ACE
Its them same acid used in etching primer.
Most paints wont bond to bare steel.
I use ospho on bare steel. It etches and coats the metal for prime or paint. It also helps keep it from rusting.
I have had bare treated steel for up to a year in my shop in the hot humid Bama...
econvenience1986 on e bay
Yes, I have 1610 (5mm lead) double start Chinese rolled ball screws on my machine. 2 of the 3 were bent, straightened best I could.
Well I got X&Y to moving today. Had it running 200 ipm rapid the full length of travel so I think I may have done something right for a change.
The X ballscrew seemed straight when I checked it but...
Thanks, I didnt remember which color but knew one was 12v and other was 5v. I will check with meter to make sure. Thanks again.
My motors,drives and bob came in and would like to start testing but the usb cord that came with it has wrong plugs on ends.
I understand this is to supply 5v for pul+ dir+ en . Can I wire from pc...
Well I took the plunge and went ahead and ordered the motors + drivers. When they get here I will be asking more questions.
i will be interested in seeing it.