505,893 active members
2,628 visitors online
Register for free
Login

Search:

Type: Posts; User: smellyfeet

Search: Search took 0.00 seconds.

  1. Replies
    10
    Views
    96

    Re: TL1 spindle RPM

    I tried that too. It made no diference also tried belt compensation in parameters, no joy. Thanks for trying.
  2. Replies
    10
    Views
    96

    Re: TL1 spindle RPM

    gregoryblane G97S1000M03 in MDI gives me 800RPM (CSS off) even after turning off and clearing the memory. Manual mode also only gives me 800RPM.
  3. Replies
    10
    Views
    96

    Re: TL1 spindle RPM

    I tried G50 S2000 no joy. I have been through all the settings in the book and changed a few relating to spindle speed still no joy. No matter what you ask for you alway get exactly 20% less.

    Its...
  4. Replies
    10
    Views
    96

    Re: TL1 spindle RPM

    Thanks Jim but unfortunately not that simple.
  5. Replies
    10
    Views
    96

    TL1 spindle RPM

    Hi. Our TL1 has suddenly started running at exactly 80% spindle speed. Eg. Demand 1000 get 800. Any ideas?
  6. Replies
    0
    Views
    72

    Spindle feedback.

    Hi, I have a Bridgeport VMC 760 with spindle problems when I start the spindle, it just goes solid.

    Can anyone tell me if I spin the spindle by hand should I get a reading on-screen like on the...
  7. Replies
    2
    Views
    676

    Re: GROSS POSITIONING ERROR S B Alarm

    Did anyone get to the bottom of this one?

    I have the same problem on my 760. When you start the spindle it goes solid but will not rotate.
    I get the error only on the first tool change attempt...
  8. Replies
    0
    Views
    427

    VMC600 table removal

    Hi.

    We have a problem with the lubrication on our VMC600-22 digita in that the oil is not being pumped to the bearings and ball screws. It is getting to the small union under the motor-end cover...
  9. Thread: MTV-310

    by smellyfeet
    Replies
    1
    Views
    344

    Similar problem here. Did you figure it out? Is...

    Similar problem here. Did you figure it out? Is there some way to reset all errors.

    Thanks.
  10. Replies
    4
    Views
    160

    Hello Fella. Its definitely a 6h thread that is...

    Hello Fella. Its definitely a 6h thread that is specified on our customers dwg. The Machinarys Handbook does go into some detail about calculating a "h" thread at the bottom of the 6g standard...
  11. Replies
    4
    Views
    160

    6h metric thread calculation

    Hi. I have just replaced my blown cranial gasket and am ready to try again.

    I am trying to figure out how to calculate the 6h tolerance position for a M24 x 1 thread and I cannot get my head...
  12. Replies
    0
    Views
    487

    Emcoturn 220 turret problem

    Hi all...

    Does anyone know anything about the Emcoturn 220? There was a turret hang up when it indexed with a too long tool which caught the guard. It blew a chip and cap on the positioning...
  13. Replies
    4
    Views
    1,201

    Thanks G-Code junki but that was obviously the...

    Thanks G-Code junki but that was obviously the first thing I did.

    The machine would not zero as per the manual so I phoned Citizen and the guy in the service dept told me it was the batteries, so...
  14. Replies
    4
    Views
    1,201

    Citizen A32 Z70-0001 Zero position error

    Hi,

    Does anyone have the procedure for clearing the error " Z70 - Abs posn ref pt set incomplete 0001 Z2 $2"


    Thanks.
  15. Replies
    12
    Views
    2,193

    Hi Mate. Did you fix it?? I just had the same...

    Hi Mate. Did you fix it?? I just had the same problem on mine turned out to be a loss of the timer information. Try manually actuating the turret by pushing a small allen key into the back of the...
  16. Hi, Have you tried starting the controller while...

    Hi, Have you tried starting the controller while holding P and Cancel then zero return?
  17. Replies
    7
    Views
    706

    Sorry, I have been on paternity leave for a...

    Sorry, I have been on paternity leave for a couple of weeks. Thanks for your answers, I have just topped up using water and got the refractometer readings back on the scale (roughly 5%). One thing...
  18. Replies
    7
    Views
    706

    Coolant, mixing in more water

    We use Castrol Hysol EP soluable and after a couple of weeks of evaporation and topping up the refractometer reading goes off the scale.

    I was told by Castrol and the rep that you shouldnt top off...
  19. Replies
    12
    Views
    701

    Thanks for all your suggestions, I am going to...

    Thanks for all your suggestions, I am going to try a modified version of the paddle wheel that will look more like one of those 1970s drinking flamingos.

    We are also going to try cork chips.

    I...
  20. Replies
    12
    Views
    701

    My bits are dented

    Hi all,

    On night time running, my lathes are reliably churning out parts but that is where it all goes wrong. The parts are falling into a container with either de-watering fluid or water with...
  21. Replies
    0
    Views
    205

    TL-1 Post processor

    Does anyone have a post-processor for a TL-1 any cam system will do.

    Thanks.
  22. Replies
    25
    Views
    1,029

    Hi, What was the problem in the end? I am...

    Hi,

    What was the problem in the end? I am having a prob with my Hurco BMC 20 the post processor I have is driving me crazy as I have to spend ages on the machine editing.

    Thanks.
  23. Replies
    12
    Views
    1,727

    Hi, Did you have any luck finding one? I need...

    Hi,

    Did you have any luck finding one? I need the same thing but I am having a hard time location one.

    Thanks.
Results 1 to 23 of 23