584,802 active members*
4,926 visitors online*
Register for free
Login

Search:

Type: Posts; User: giahinader

Search: Search took 0.00 seconds.

  1. Replies
    19
    Views
    6,334

    Re: Loosing PLC program on FIDIA F1.0190

    please send a closer shot of the control racks .The signs on the racks are not clear.
    Also a shot froam the side of the control that has the model label.
    Nader
  2. Replies
    19
    Views
    6,334

    Re: Loosing PLC program on FIDIA F1.0190

    Please contact me by [email protected]
  3. Replies
    19
    Views
    6,334

    Re: Loosing PLC program on FIDIA F1.0190

    FIDIA Digit 165 is the model of the machine.What is the model of the control of your machine?
    Please send some pictures of the monitor and floppy drives(if exist) of your machine addition to...
  4. Replies
    19
    Views
    6,334

    Re: Loosing PLC program on FIDIA F1.0190

    Please send some pictures of your control like the samples I have attached.
    Nader
  5. Replies
    19
    Views
    6,334

    Re: Loosing PLC program on FIDIA F1.0190

    Hi,
    I will ask about FIDIA Digit 165,
    Nader
  6. Replies
    19
    Views
    6,334

    Re: Loosing PLC program on FIDIA F1.0190

    Hi,
    Some people like me always think of the worst.
    If I could write my mistakes it would be more than a 1000 page book.
    Best Wishes-Nader
  7. Replies
    19
    Views
    6,334

    Re: Loosing PLC program on FIDIA F1.0190

    Dear Juha,
    I am not familiar with FIDIA Digit 165 My control is a FIDIA F1.10190 control.
    If you have not made DNC connection yet I can ask about FIDIA Digit 165 for you,There are so many FIDIA...
  8. Replies
    19
    Views
    6,334

    Re: Loosing PLC program on FIDIA F1.0190

    Dear Sir,
    I just saw your post.
    I have a FIDIA F1.0190 control.
    I am not familiar with FIDIA Digit 165.
    My machine connects to PC by a 9 pin RS232 cable from SLU2 on control to a PC using FIDIA...
  9. Replies
    19
    Views
    6,334

    Re: Loosing PLC program on FIDIA F1.0190

    After 5 years the problem of loosing plc program is fixed.
    The original battery on the cpu board was a packed box made in FRANCE .
    There were two 1.2V coin batteries in this box.
    I replaced the...
  10. Thread: Fidia F1

    by giahinader
    Replies
    4
    Views
    7,597

    Re: Fidia F1

    I can tell you how to change the error messages to English.
    Are the softkeys signs of your machine in German?
    Mine is english.I can ask from FIDIA company if its possible to
    Change the main...
  11. Replies
    19
    Views
    6,334

    Re: Loosing PLC program on FIDIA F1.0190

    Hi,
    A cable with two 9 pin RS232 connectors is needed.
    One to your PC and the other to SLU2 on your machine.
    You must run FIDIA DNC software on your PC then WKS connects to your PC.
    I can mail...
  12. Replies
    19
    Views
    6,334

    Re: Loosing PLC program on FIDIA F1.0190

    Hello,
    I got a used Cortini M500 3years ago.Machine was out of operation and I repaired the spindle drive,Y axis ball screw bearing,lubrication tubes of X axis,flattened the work table and many...
  13. Replies
    19
    Views
    6,334

    Re: Loosing PLC program on FIDIA F1.0190

    The battery in the VGR board saves the VGR settings.
    I have already replaced both batterys one in CPU board another in VGR board,but loosing PLC program after each startup.
    Thank you very much.
  14. Replies
    19
    Views
    6,334

    Loosing PLC program on FIDIA F1.0190

    Hi,
    I loose PLC program after each turn off of the machine.
    Already replaced the battery on the CPU board,but no success.
    Appriciate any help.
  15. Replies
    0
    Views
    1,397

    810ME(PP-Memory wrongly formatted)

    Hi,
    After repairing a hardware failure due to a electric power shut off on a 810ME I get the error message(12 PP-Memory Wrongly formatted) in the BTR Start mode.
    Recieving&sending files in DATA...
Results 1 to 15 of 15