So I am installing a Fagor 8055i on a roll turning lathe. The company has several. The spindle driver is a Baldor BC30D7. I have no way to reprogram the drive to the Fagor. I would appreciate it...
Type: Posts; User: amtekinc
So I am installing a Fagor 8055i on a roll turning lathe. The company has several. The spindle driver is a Baldor BC30D7. I have no way to reprogram the drive to the Fagor. I would appreciate it...
I am retrofitting a machine that came with a TNC 320 (MC 320) and it has no wiring diagrams. I have been looking for software to read the PLC program to no avail. I have tried to find the TNC 320...
Make sure your shield is only grounded on one end of the encoder cable. Also, make sure that the encoder cable is not near the motor power cable as this can induce noise into a cable even if...
Had the same thing happen to me. I had the marker pulse hooked up on the not A of the differential inputs. Make sure that it is hooked up correctly as connecting the marker pulse up to the A or B...
It works! Thanks, so much.:cheers::cheers::cheers::cheers:
Customer lost all option parameters on a Blue Chip V4220 with 0-MC. I need the spindle orient option bit. Fanuc will not help even though controller is very old. THEY ARE AFRAID I WILL ROB THE OEM...
The machine is an OM VTL that started life with a 6TB controller. My client wanted to save money on a retrofit, as he is a machinery dealer, and put this 18T-b controller on the machine. We are...
Thanks. I found the manual, verified the plug in boards and found the problem I was having with SRAM parity error was due to not clearing the SRAM before boot load. Once I did this, the system...
Do you know what manual number that would be?
I have checked these parameters,signals and more. I was able to take the From card from another controller and put it in the ailing controller and was able to jog. Things were looking up when...
I am installing an old 18tb on a vtl. It was previously a 4 axes and now is a two axes. The problem is that it will not jog even though every interlock and signal is satisfied. Fanuc cannot...
Thanks, Mike!
I did find the problem. It was one of the two power darlingtons in the regen circutry. For some reason when i was checking resistance on this device, I overlooked the B1, E1...
I will look at it if you still have a need for it. Let me know.
Ok. This is an old timer and probably should be replaced, but, the customer has a spare unit (broken) and wants me to make a good one from two broken drives. The one to be fixed is working with one...
60 amps is the requested amps.
I am in need of build plans and schematics for an EDM generator with gap controlled hydraulic servo. I have a servo amp, but, need the generator and gap control circuity. The old supply was a 20...
I have a customer who is looking to replace a power supply on a conventional edm. Where can I find a company like Sparcatron who used to sell just the generator? Searching the web isn't working.
Do you know if the wire will feed manually when this occurs? Thanks, by the way, as I have learned more about this machine from troubleshooting and from the other people like yourself, than I have...
Since my last post, I have fixed the problem and am not certain as to how i did it. I had the operator set up the machine to run a program and then I forced the wire feed through diagnostics and it...
I am not at the machine today, however, I did check this and did find what I thought was a reasonable wire feed rate for the M-codes.
I have looked at all of the parameters regarding the wire feed and can manually force wire feed on in the diagnostics, but, in normal operation the relays for wire feed turn on and then off almost...
I have been working on repairing a Makino EC3025 with a wire feed problem. Service tech was adamant that I had a connector problem on the WCC board or a bad $5100 board. Not so. I was able to...
Some of the Westamp engineers left the company to start Servo Dynamics. They make some drive cards that are virtually interchangeable, that tune the same way and you can still purchase them from...
I have a malfunctioning A711-30151-112 Westamp driver. Will a 30150-148 work as a replacement?