Here is what I put in and it loaded and ran , after I bought a battery pack that held regular batteries and plugged back into board, air pressure good , started machine and it came up to that page...
Type: Posts; User: Rondal
Here is what I put in and it loaded and ran , after I bought a battery pack that held regular batteries and plugged back into board, air pressure good , started machine and it came up to that page...
yes It works now, I had a dead memory battery and it came up with a different page on start up , i entered the new numbers and it took off and runs. I'm not the expert but I will try to help. Thanks...
Thank You I think I am going to check into that. Thanks again For the info Rondal
Thanks
Its been sitting idle for probably over a year now and the memory battery died and then thats when the fun started . I knew I was in trouble as soon as I didn't recognize that screen...
bloke
It works now. The spindle adjusts to called up program speed. Thank you so much for the help. When I started looking into this forum, I noticed your name a lot and by reading the times...
Bloke
I measured the voltage on lead #2 containing red # 8, white #9 wires. Its 127 Volts AC. Looks like the board AC in says 8 HOT, 9 COM . . Does this sound right? Sorry about the drawing mark...
Bloke
Thanks for the help. I tried several numbers on the start up BIOS page, the ones you gave me did not work so I started removing the boards from the back plane and reinserting them. I found...
This 3.2 GB drive is the drive that has been in it, I have not changed anything but replaced the Rayovac alkaline 840 4.5 v battery . I took the connection off of that battery and used it on a ...
This is the drive in Hurco KM5P Thanks Rondal
sorry that is the wrong hard drive picture, Its not a 160 GB .
here are some photos of hard drive, screen bios page, Edit , The 160 hard drive is not the correct picture for the Hurco KM5P Thanks Rondal
I entered cylinders 6256 , heads 16 , sectors 63 enter and saved , enter, no change, shut off machine at disconnect and restarted , no change. I noticed that the revision is still at 1.0, how do I...
I entered cylinders 6256 , heads 16 , sectors 63 enter and saved , enter, no change, shut off machine at disconnect and restarted , no change. I noticed that the revision is still at 1.0, how do I...
I entered cylinders 6256 , heads 16 , sectors 63 enter and saved , enter, no change, shut off machine at disconnect and restarted , no change. I noticed that the revision is still at 1.0, how do...
Thank you for the reply, I had a dream that woke me up out of asleep about a part for whatever reason and decided to check this post , Thanks again for the reply and I will try that today .Thanks...
Battery died and replaced it with 4.5 volts the screen is asking me to choose , This screen is new and probably because it lost memory
.here are the question s on start up
MOS SETUP -REV 1.0...
Hurco KM5P Max 32/DSP I replaced a dead 4.5 v memory battery on the board but when I start machine it wants me to choose hard drive type? I realize that probably all memory went away so thats why...
Hurco KM5P with MAX 32/DSP control not booting up. It did work but now doesn't. I let it set idle for probably a year. Screen that comes up first I have never seen before. shows CMOS SETUP-REV 1.0...
Ditto the situation is the same on this Hurco KM5P. Servo drives code error base current is blocked, machine is in E stop.? I believe there is only one E stop button on machine and it seems to be...
[B]HURCO km5p not working servo boards lit up with code base current is blocked the codes probable cause is that machine is in E stop. I do not know of any stop button other than the one on the...