584,866 active members*
5,286 visitors online*
Register for free
Login

Search:

Type: Posts; User: mejasont

Search: Search took 0.00 seconds.

  1. Replies
    3
    Views
    3,923

    Re: Discussion on HAAS DPRNT

    Change the Baud rate to 115200 if your machine can do it, that fixed the buffer overflow issue for me. looks like the machine processor hates being delayed sending out serial data so the faster it...
  2. Re: Older Haas DIY cheap Probe - Guide with pics and video

    Cheap Broken Tool Detection for Haas - Wiley Davis

    This page from Wiley is absolutely spot on and incorporates integration into conFusion 360
    the Skip controlled tool height setter works a treat....
  3. Re: Older Haas DIY cheap Probe - Guide with pics and video

    @ brianbonedoc

    Brian, from your code examples, you have some for tool height settings.

    I have tried one but it has left me with a couple of questions

    %
    O03302;
    (T2 Measure);
    T2 M06
  4. Re: Older Haas DIY cheap Probe - Guide with pics and video

    Hi Everyone,
    im still keeping this thread alive. Its like a right to repair for those of us who own older Haas machines.
    I have followed this most excellent topic and acheived the goal of getting...
  5. Re: Older Haas DIY cheap Probe - Guide with pics and video

    nothing to enable.

    just make sure you are joining the correct 2 wires on the i/o board skip plug connection

    when you join them together you should get a beep and it also shows up an event in...
  6. Re: Older Haas DIY cheap Probe - Guide with pics and video

    Hi Metalcutter

    thanks for your reply, i got sorted in the end.
    I was new to the controller and didnt quite grasp the layout of the screens.
    i found out that the parameters screen ? (not...
  7. Re: Can Hass Mini Mill with high voltage transformer run on 2 phase power?

    Ok be wise and be careful, my conversion didnt quite go to plan. It is as straightforward as it sounds provided you dont have a vector drive - vector drive not possible apparently.
    If your mini...
  8. Re: Older Haas DIY cheap Probe - Guide with pics and video

    Hi Everyone, i hope you can point me in the right direction.
    I have a Haas Mini Mill Built 2002 with a CHC control and software version 11.17
    im having trouble finding the SKIP input on the...
  9. Replies
    9,196
    Views
    334,464

    Re: The Coming Climate Change

    The rocket science part is :- The earth warms up (that killed the dinasours) the earth gets flooded then it freezes. The clue is the fact they had to drill 300ft down into the polar ice caps to...
  10. Re: Can Hass Mini Mill with high voltage transformer run on 2 phase power?

    This is about as good as it gets, but im still delving into it to be fair
    J.
  11. Re: Can Hass Mini Mill with high voltage transformer run on 2 phase power?

    Sorry yes i have a 60A supply, actually its a 100A fused incomming supply but im sure they dont want me to peek that. lol.
    All this because i cant get 3 phase yet, the building trade has hammered...
  12. Re: Can Hass Mini Mill with high voltage transformer run on 2 phase power?

    Hi Mactec

    Thanks for your reply.

    I had read that i needed a seperate earth cable ran and have planned to route it with the 6mm (8 SWG) SY Flexible cable back to a 40A type D MCB via a rotary...
  13. Re: Can Hass Mini Mill with high voltage transformer run on 2 phase power?

    Haas's own documentation describes the connection of "Single Phase 240v" to the mini mill
    In Operators Mini Mill Addendum ES0205l see attached pages

    From this instruction i understand the UK...
  14. Replies
    39
    Views
    19,224

    Re: Entering every Haas unlock code

    But there would also be no need for forums like this either, you would certainly loose your stage my friend as would many others.
    i would like to have the gentlemans email puerly to ask after his...
  15. Replies
    8
    Views
    2,467

    Re: This G-code malfunction is MIND BOGGLING

    Are you hand writing your code or is it from the post processor in your CAM.
    Im confused why you have rapid moves whilst the tool is engaged in the work piece ie Z0, Z-1. normal behaviour would be...
  16. Replies
    39
    Views
    19,224

    Re: Entering every Haas unlock code

    Its not ilegal. take a car for example you are not told how to drive it or that you shouldnt hit it with a sledge hammer, buth of which would void your warrenty but not ilegal. What would be...
  17. Replies
    39
    Views
    19,224

    Re: Entering every Haas unlock code

    If you buy a secondhand machine and cant repair it because its locked access, then you would know why the chap wants to break the code.
    hass have not done it out of the goodness of their hearts,...
  18. Replies
    15
    Views
    1,903

    Re: Serial command set for ATC - Interfacing

    This looks like that giant leap for man kind:devious:
  19. Replies
    15
    Views
    1,903

    Re: Serial command set for ATC - Interfacing

    Any chance of a boot up the arse in the right direction. I keep scouring through any file which hints at a name with ZBot in it hoping to find "VE" without success (It may be different for the ATC)...
  20. Replies
    15
    Views
    1,903

    Re: Serial command set for ATC - Interfacing

    ha ha the man himself, It is your teensy code is it not. jwatte. you are a god.
    I was wondering tonight why i couldnt find an uno with an FTDI when i looked in my box of bits. I can remember back...
  21. Replies
    15
    Views
    1,903

    Re: Serial command set for ATC - Interfacing

    I have been in touch with this guy - David
    https://www.youtube.com/watch?v=nQDUkIXAy2w
    He has designed and built a controller for an ATC based on the arduino UNO. it would depend on how much he is...
  22. Replies
    15
    Views
    1,903

    Re: Serial command set for ATC - Interfacing

    Thanks Steve,
    I have left a message on his channel and hopefully i will here back from him.
    Progress so far - the reprogramming of the usb bridge's id didnt work very well, at all. The appear to...
  23. Replies
    15
    Views
    1,903

    Serial command set for ATC - Interfacing

    Im trying to work out how to interface with PP to build an ATC.
    The USB/serial device is a silicon labs IC, im sure that using silicon labs device tools i can reprogram the devices serial number to...
Results 1 to 23 of 24