Mori DMG NLX1500 lathe with CELOS control.
Y-axis on our machine is off by about 0.06 and I like to re-zero the y axis. Does anyone know how? Parameter number?
I know how to do that on NL1500 but...
Type: Posts; User: teal854t
Mori DMG NLX1500 lathe with CELOS control.
Y-axis on our machine is off by about 0.06 and I like to re-zero the y axis. Does anyone know how? Parameter number?
I know how to do that on NL1500 but...
How can i disable 4th or 5th axis on Mori MV5000?
Which parameter do i need to change?
Thanks
Haas 5C controller box (black box). Need parameter list for 5C controller box. It shows 14 parameters. I have HA5C but different.
Thanks
I'm trying to attach pdf file to the post. How do I do it? I can inser image and video but how do I attach a file?
Thanks
I don't know much about SV50B. We have a few NV5000 and throwing tool from ATC arm. Replaced springs and piston and still throwing tools. Finally found out that there's a rod and a collar at the...
701 alarm, fan motor overheat. Found 2 fans on spindle drive and power supple unit. Replace both and still shows 701. Original fan was Toyo fan but buy replacement from Mcmaster, 230v 10-12W fans....
Need instruction on how to set zero (home) position on NL1500 with Mitsubishi control. It's different from Fanuc.
Thanks
It is not a touch screen.
We have Mitsubishi EDM model EA12ME (EA Series) and something went wrong, it didn't boot completely and froze. So we did restore and boot up fine now. But lost the parameters. How can I get to...
We have six NL 1500 about 6 years old and almost all of them had main clamping unit hydraulic leak within 2 years and ended up replacing them. Some of them had hair line crack and could not be...
When I press optional stop (OSP) button machine does not stop after tool change, it continues to next tool and so on. Do I need M1 or OSP should stops without M1? Is there any parameter or setting to...
Hi
we have 12 Mori NV5000 with operator's sliding door has window (glass). They are all yellowish (caused by coolant) and can't clean them, stuck on glass. Tried windex, and other cleaners, didn't...
Not sure. It shows MSG 501. It doesn't have usb. It has flash card slot. It is a 2002 machine.
I found the Timer and Power Standby screen under Setting menu. Under Power Standby, screen saver timer and other timers are turned off, back light is set to high. When screen went blank I had to shut...
I have no idea of how to get to power save and screen timer.
Thanks
Mori NV5000 screen goes blank. Screen comes back on after shut it down and leave it for an hour and turn on it back on. Then suddenly screen goes blank. Replaced screen back light and ballast board....
Our machine Z-axis Ref (Home) position is little bit low. When it changes tool tool holder arm is almost hitting. How can I adjust Z-axis Ref position?
Thanks
Hi
We have about 12 years old VF3 with floppy drive. How can I tell if it has hard drive or not? Where are all files stored at? Is there any IDE connector so I can hook up IDE to CF adapter. Floppy...
We used to communicate to the machine with our laptop with rs232 db9 to db25. Our IT ran rj45 cable to the machine and like to to know how we can connect through network to our desktop. We have Digi...
A and B axes are for rotaty and tilt table made by Nikkin. There's no symtoms, the indexer/rotary unit ran fine for a hour or some times the whole shift. Then stopped and came up with 411. We had to...
We have Gilsemeister DMG Twin 65. Alarm code 25000: axis X1 hardware fault of active encoder. First we replace motor encoder cable, proble went away for about 2 weeks and came back. Then we replaced...
I like to know how I can increase storage memory for 18i? Is there a parameter for it? I have 12k byte available.
Thanks
We have Mori NV5000 with Fanuc 18i. The program directory available memory for files is about 127k byte. There's parameter to increase the storage memory. Which parameter is that?
Thanks
We have horizontal mill with indexer and rotary units. I like to disable the rotary unit (A-axis) because the motor was removed.
Thanks
We have five, Twin 65 with SIEMENS 840D (windows 95) and one of the machines hard drive crashed. We bought a new hard drive from Bestbuy store. I like to know how I can clone hard drives. Since we...
How do I check private massage?
It is a dogless system. Y-axis for turret was off and tried changing it with grid shift (1850) but couldn't do it. whenever I change 1850 value I need to power it down and re do the Y-axis home. I...
We have Mori Seiki mill with 18i and had problem with spindle orientation for tool change parameter 4077 worked for us. Try changing parameter 4077 or check out this ...
I couldn't change the bit #4 for parameter 9936 for Fanuc 18i. I enabled parameter write and didn't work. What does 9936 bit 4 do? We need to chan the bit on inorder for renishaw probe to work....
Hi
We have Mori mill with Fanuc 18i controller. We're getting error 410, 411 and 438 for axis A and axis B. Is there any parameter that i can change to correct for error 410 and 411?
Thanks