Hi
Do you still need the I.d tags for the servo drives?, I removed mine for both
X and Y motors so I could get info for a retrofit,
And can sen pictures if you wish,
Allen
Type: Posts; User: moonman5
Hi
Do you still need the I.d tags for the servo drives?, I removed mine for both
X and Y motors so I could get info for a retrofit,
And can sen pictures if you wish,
Allen
Hi All,
I am trying to find what board on a Siemens 810t Ga3 contains the EPROMS for language change.
I cannot change the language via the control as my control does not have parameter 250 (my...
Hi,
Yes I have them, if you give me an e-mail address I can send them to you,
The parameters are for the Siemens 810t control and worked fine on my machine
Regards, Allen.
Hi all,
I have a Hardinge CHNC1 with a 810t control, I had an issue with the machine in that it would shut down imediatly the main breakers kicked in?
After a lot of diagnosing it came down...
Hi Ed,
So you have given me two E-mails what one should I send money to? bit confused with your reply,
Allen.
Hi Ed,
Yes that sounds ok to me, can you just confirm that the part is in good working order, and also I will need your e-mail address to send money via PayPal,
Thank you,
Allen
Hi Ed,
Yes I can pay via PayPal, I don't no where to start with an offer, got no idea what they cost new (not that you can get them now) I am in the Uk so obviously there will be postage costs...
Hi Ed,
Yes! that's exactly the same number, C2-137B Have you got one?
Allen.
Hi Ed,
what about a Turret encoder?
Thanks,
Allen
Hi,
Thanks for the attachment, a great help! So you don't think that with the turret encoder completely removed it will give me an E-stop? that was my thoughts? do you think it could be a faulty...
Hi,
Thanks for your reply greatly appreciated, Yes I have done that, I have also checked both e-stops with a digital meter and both are good, The machine is not on the hard stops (I always move...
Hi All,
Subject to my previous post on my Hardinge CNHC1 Siemens 810T control, So now I have managed to get the machine to power up (the fault was a short in the turret encoder) It took
me an age...
Hi,
Have you still got the Interface board?
Thanks, Allen.
Anybody had this issue with a CHNC1 Hardinge lathe? When I press the green "Control on" button (Siemens 810T) it tries to power up you see the screen light up for about two seconds and you can here...
Hi,
Sent you parameters via e-mail, It took me a couple of attempts to understand and load but I know they work! follow the instructions carefully!
Yes I do run a Harding CHNC 1, it is a good...
Hi,
Yes I have parameters and instructions on how to install, they worked perfectly on my machine, If you give me an e-mail address I can send them to you.
Kind Regards,
Allen
Hi All,
I have a Hardinge CHNC 1 with a Siemens 810T controller, I have a strange problem?
When the machine reads an M01 (or tool call) command the spindles sometimes will not come to a...
Hi djr76,
Thanks for you help, the right "shim"? by this do you mean the cutting insert?, and 1500 Rpm, that will be pretty scary watching the z axis move at a 2mm pitch rate, that sounds fast!
I...
Hi All,
Can anyone help?
I am trying to create a 20mm x 2mm pitch thread on low carbon (free cutting) Mild Steel, I am getting a poor finish? under a magnifying glass the surface looks "torn"
...
Hi,
Can anyone help? I have a Hardinge chnc1 with a 810T control, I am confused as to why the setting/tool/G54 screen always displays in imperial? How do I get this to display in metric?
I am...
Hi All,
Can anyone help?
I have a Hardinge CHNC1 with a Siemens Genumerik 810T control, I have recently re-installed the commissioning data/Parameters after loosing data thro battery back up...
Hi All,
Can anyone help, I am to say the least confused?
I am currently wiring the motor on my home built rotary phase converter, I can wire the motor in "Star" but this gives me output...
Hi,
Thanks for your reply,
That makes sense,
Thank you,
Allen
Hi Larry,
Thanks for your reply,
So there is a difference in "power factor capacitor" and a "start/run" capacitors?
Allen
Hi All,
Can anyone help? I am in the process of making my own 20Hp Rotary Converter, I have read many discussions online about the use of "Power correction capacitors" to "tune"
the three phases...
Hi Mike,
NICE! love the wiring, very neat, and those capacitor clamps are brilliant, I am gonna give it a go, already got the "pony" motor, got my eye on a couple of 3 phase motors on e-bay,
got...
Hi John,
Thanks for your input, At the moment I have no 3 phase to the machine at all (only the 120 volt via the control transformer to the controller) I really would like to get a good stable 3...
Hi Mike,
Hi Mike,
Yes I do, I need the complete unit, the battery holder and the battery case (my one has just fallen to bits?, the bits of casing were laying next to the monitor in the control...
Mike
A masterpiece! did you do the drawing on a "Etch-a-Sketch"! lol,...... Ok so I kind of understand the circuit, but what happens to the small start up motor once the 3 phase motor is going, ...
351126351128Torin,
I am not supplying single phase to a 3 phase device (this obviously will not work) When I got the machine it had a controller fault, so while waiting to find some way of getting...