Hi,
Try to change Param #909.3 to 1.
Let me know the result.
Thanks!
Good luck
Type: Posts; User: CNC SERVICE
Hi,
Try to change Param #909.3 to 1.
Let me know the result.
Thanks!
Good luck
Hi,
Normally, if G code unavailable in the system lists, the system will issue P/S alarm no. 10 Improper G-Code. But in your case issue atc alarm, I never heard this alarm before. Pls check what I...
Hi,
Pls try the below program then see it what happen,
M6T1;
G54G90G0 X0 Y0 S1000 M3;
G43Z50.0H1;
G98G83Z-10.0Q5.0R3.0F200;
X-50.0Y-50.0;
X50.0;
Y50.0;
If your ROM having programe inside try Param #901.7 change it to 1.
Good luck.
Hi Rai,
Sorry to tell you that I can't email you, it seem that you are unlucky to receive my manual. It always denied from your server many many times.
This is an message from our mailbox,
...
Hi Rai,
Pls check your email.
Normally, you can try to take off the PMC card from mother board then power on. If the system boot up to normal status I mean at Position page but getting EMG or Not...
Hi,
Normally, we use G10 on the top of the program.
Ex.
O1234;
G90G10L2P1 X_Y_Z_;
;
;
P0 = Ext.
P1 = G54
Hi,
Normally, when you clear paramerter , the system will automatically set up to Chanel 0, Baud Rate 4800. First, press EMG. switch then go to PARAMETER page then try to find [READ] at the softkey...
Thank you very much for your great information. After I study M2 manual I found that the card name like FX cards, they are not same. I want to know all system structures so that I can clear and...
Check your email of both guys, I have sent them and some basic procedure for you.
Thanks!
Hi all,
I am looking for Mazatrol Cam T2 (Hardware & Software) manual. I can't find in Meau site. I only found M & T plus, M3, M0 and M2 manual in there. Any one known kindly inform.
Thank you.
It is very hard to say that it came from this card, some time Master card, PSU, Fuse and 24v shorted ground and so on . I think better you call Fanuc local service for this problem. I have...
Hi All,
Any one know where I can download manual from? Like Meau site they have all manual.
Thank you!
pls contact me at 081-351-8301. i can help you to repair your Okuma machine.
Thanks.
Hi,
I will explain you for the sequence of ATC tool change,
After you give command M6 they will function as follow,
1. Pot down (Finished signal by Limit or prox. switch)
2. Arm rotate to...
Hi all,
I would like to ask some one who expert about how to check Fanuc Servo Alpha Series,
The problem is 401 Servo ready off (VRDY). Some time PSM, SPM and SVM defective, How can I know which...
What machine brand and model? I think the problem came from ATC interlock which MTB had wrote in ladder. Basically check at PMC parameter. If parameter okay, send me ladder diagram then I can help...
PLS CALL SERVICE CALL CENTER ASK THEM THE PROCEDURE TO DO THIS JOB(THEY HAVE PEPER LIKE I HAVE BUT MANY MANY PAGES). THEY HAVE QUITE ALOT MANY POINTS COMPLICATED, ESPECIALLY W AXIS AND Z AXIS IF YOU...
Well, as your question MSC-518 is Fanuc-18 Series but I'm not sure your model may be Model B or C. You should look at Fanuc Data sheet which attached inside the Electrical book then you can find an...
FIRST OF ALL, CHECK THE MAGAZINE DRIVE UNIT WHAT ALARM NO. SHOWN ON LED 7 SEGMENT, IF JUST ZRN LOSTS POSITION THEN I HAVE PROCEDURE TO RESTORE IT.
THANKS
[email protected]
CONTACT ME I'M MORI SEIKI"S ENGINEER AT [email protected]