Search:

There are barrier settings on tool set page, but still cannot guarantee that you wont crash, long jaws boring tools etc. Check 1st off at low rapid rate.

It is a problem with axis drive. I have found that putting a heater (light bulb) in cabinet works sometimes.

How to clear asterisks on T1. You will need to take note of parameters first.

to clear all rubbush on T1
Press MENU key. Press Param. press PAGE, bring cursor to OP12, press
111111118 IMPUT...

Hi Bob, I have checked all breakers. It does start ok and runs for up to 10 minutes before I get "trip breaker" alarm. It will then not start again for at least 2 hours. I do not reset any breakers....

Hi , I have a QT10 T Plus. It starts up ok and runs in AUTO for about 10 minutes then it stops an I get alarm TRIP Breaker and Emergency stop. Does anyone know what would cause this.

Had it been working ?.. Is it possible that motor is running wrong direction ?.

Hi, I cant see anything wrong with program. It looks like thread is not deep enough. Are tools set correctly or are there X offsets on tools ?.

Just wondering if you got it sorted. I have 4 Mazaks with T1 control. I could send copies of parameters and instructions how to reinstall them.

We have it running fine now. We got service engineer to look at it. We had shorted out the pressure switch which was used on old system which was fine but the other ends of the wires had become...

Hello, I have a Webster & Bennett 36" vertical borer and I turned the chuck clockwise by hand by mistake and now the rapids do not work. There is a warning on machine not to turn backwards by hand or...

Found it. Option when I open new file. Thanks.

I reinstalled GibbsCam and now it is inches but I need to change to metric but can't see how to change it. Can't find anything in manuals.

Thanks, I will let you know how I get on.

The older Mazak turrets were operated by air over hydraulics not connected to hydraulic power pack. I am trying to convert to using power pack system off scrap machine. That is correct when I power...

I still have alarm and cannot clear it. I have checked our other Mazaks and they do not clamp when powered up, thats why we have to unclamp and clamp after startup. They are air over hydraulic, it is...

I should have given more information. My machine could not run without air as it is air over hydraulic clamping, I think hydraulic clamping and air unclamp. We have another scrap machine with all...

It has not been running for a few months but we power it up most days. We were having a problem with turret clamping( air over hydraulics).

We have a Mazak QT 20. When we start it we get fault"emergency stop" without any details such as "air pressure" etc. Any ideas ?.

Hi. I have a QT 20 T1 with Freqrol FR-SF 22K spindle drive with power supply blown. I have a scrap machine with FR-SE 22K. Does anyone know if I can swap drive ?.

How to clear asterisks on T1. You will need to take note of parameters first.

to clear all rubbush on T1
Press MENU key. Press Param. press PAGE, bring cursor to OP12, press
111111118 IMPUT...

It might be power supply which sits on top of drive. I have QT20 with same problem.

It seems like you have .1 lead in and away from toolpath.

You can download simulator from Hurco website or you could get it in usb stick but it runs for only 1 month on same computer. You could then run it on second computer for month.

You are right, just enter 29 deg, you may have to enter depth of thrd.

I use camlink from Griffo Brothers or Mazlink.

We have the same problem with QT 20 , we changed x axis drive with one from scrap machine and it worked OK for a while. We then got errors in both axis, we slowed down rapids in parameters and it is...

Have you tried adjusting proximity switches on chuck cylinder or disconnecting them ?.

No problem lifting with forklift close to floor but much safer to lift with slings off truck.

I have QT20 T1, if I set spindle rev clamp at eg 800 it works right in gear 1 but goes to 1200 in gear 2. It used to work right but changed without me knowingly doing anything.

Hi
My monitor on Mazak T1 packed up so I bought converter to VGA . It is named XVGA Box. I am connecting machine to XVGA using 9 pin. On the instructions the colours of the wires are red ,green and...