523,794 active members*
1,813 visitors online*
Register for free
Login

Search:

Type: Posts; User: mbservice

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    422

    Re: Fanuc OTc 414 X axis detect error alarm

    have sent you a pm
  2. Replies
    3
    Views
    422

    Re: Fanuc OTc 414 X axis detect error alarm

    Did you check the encoder ?
  3. Re: 1337/5000 TNC155: Data in RAM but inaccessible

    Your batteries have failed
    When the parameters are loaded they would come up with a ? You would not be a me to go back it would come up with a ? Again
    Unless all the parameters are fully loaded
  4. Re: Bridgeport Interact 1 Mk2 with TNC 2500 missing 110V on wire 8 and 9 when power o

    nikos
    Did you check the overtravel switches
  5. Replies
    16
    Views
    4,326

    Re: Colchester 2000L

    What turret do you have ? Do you have a barfeed? What is your problem?
  6. Re: Bridgeport series 1 interact TNC 145 Gross positioning error B

    Check your speed parameters
  7. Replies
    11
    Views
    1,638

    Re: Colchester Tornado 200 Lathe parameters

    Hi Vlad
    Tornado 100 parameters will be close but not correct as there are different models and veraions of the machine you may cause damage to your drives please send me your email address in a...
  8. Thread: Fanuc 21i TB

    by mbservice
    Replies
    3
    Views
    39

    Re: Fanuc 21i TB

    What do you mean it won't pick up the wear offset
  9. Replies
    3
    Views
    28

    Re: Fanuc Flash Card

    Use the SRAM service page
  10. Replies
    2
    Views
    737

    Re: align MF Sprint 65 Revolver

    Dont suppose you have a back up of your machine
  11. Replies
    0
    Views
    162

    Re: help for fanuc 0-TT

    What is your incoming supply ?
    Where are you getting 410V
  12. Replies
    3
    Views
    42

    Re: YAM lathe with 6t

    Try stopping spindle , turning off coolant etc to see why it's not stopping
  13. Replies
    3
    Views
    42

    Re: YAM lathe with 6t

    What happens if you change M00 to M30 does program stop and reset
  14. Re: Replacment battery backup board for HAAS Machines

    How much please pm me
  15. Re: Parameters for Colchester 2000 with 0-TC control and 8 station Duplomatic turret

    Did you get the lathe going
  16. Re: EX1104 TURRET CLAMP/UNCLAMP SENSOR ERROR or OVER 1SEC

    Does the turret release within 1 second may be wise to remove sensor check it's working and clean it
  17. Re: 1337/5000 TNC155: Data in RAM but inaccessible

    What happens if you load all parameters then reboot system
  18. Re: 1337/5000 TNC155: Data in RAM but inaccessible

    If you type in the correct value and press ent does the value change
    When you're accessing them do you put in the unlock code
  19. Replies
    7
    Views
    926

    Re: PMC Of Colchester Electronic Triumph

    Hi yes I have parameters for your machine please send the serial number and your email
  20. Replies
    11
    Views
    1,638

    Re: Colchester Tornado 200 Lathe parameters

    What does it say on the screen when you power up
  21. Re: HELP! CNC Engineer needed, any thoughts?

    Private Message me if any problems Im in Kent
  22. Replies
    4
    Views
    49

    Re: Colchester 2000L Parameters

    Brent messaged you its nothing to do with parameters I work on thise all the time
  23. Re: Dugard eagle 100 lathe. Fanuc series oi mate-tc

    Chuck sensors? What alarm is on the drive
  24. Replies
    1
    Views
    55

    Re: Colchester mbf1000 barfeed issue

    Have you set the number of bars you want to run in the barfeed operation page
  25. Replies
    1
    Views
    53

    Re: Fanuc noob question q setter

    Only if you have told the control you are using that tool in MDI
  26. Re: Bridgeport Interact Series 1 - TNC145 Tapping Cycle Issues

    Message me your email or phone number and I'll send you a pic as I'm in Kent
  27. Re: Bridgeport Interact Series 1 - TNC145 Tapping Cycle Issues

    You may be able to get away with spring loaded collets dependant on speeds and tap size
    Where are you based
  28. Re: Fanuc 10T Direct drawing dimension programming

    Hi Kesseli
    That looks like the Fanuc manual so would show it but does not mean it was activated by the manufacturer
  29. Re: Bridgeport Interact Series 1 - TNC145 Tapping Cycle Issues

    Yes as the spindle slows the head allows the tap to float down a couple of mm's and on retraction it starts lifting up preventing threads stripping
  30. Re: Bridgeport Interact Series 1 - TNC145 Tapping Cycle Issues

    There is no rigid tapping on that machine change to a floating tapping head and will solve problem the dwell allows for the spindle to stop and reverse
Results 1 to 30 of 458
Page 1 of 16 1 2 3 4