Has anyone here succcessfully configured EMC to run the CNC4PC C6 Spindle control card? I seem to be partially there but I cannot figure out how to configure HAL to output my signal at 25kHz.
...
Type: Posts; User: DanC
Has anyone here succcessfully configured EMC to run the CNC4PC C6 Spindle control card? I seem to be partially there but I cannot figure out how to configure HAL to output my signal at 25kHz.
...
Thanks Big John T. I'll let you know how those work out once I install EMC.
I am using IM483 drivers (Intelligent Motion System). I found these specs in the user manual in a table named 'Logic Input Timing', but I am not clear how I interpret them for the driver timing...
Jason,
In a nut shell, you need a computer to interface with the CNC Brain. The CNC Brain is a motion controller. It "hooks up" to servo or stepper motor drives (could be Gecko's if you choose). ...
Jason,
In a nut shell, you need a computer to interface with the CNC Brain. The CNC Brain is a motion controller. It "hooks up" to servo or stepper motor drives (could be Gecko's if you choose). ...
Mcyoda,
It sounds like you are working on your first machine. The CNC Brain is still in Beta testing and, in my opinion, is not be the right solution for someone just getting started in CNC. ...
Mcyoda,
It sounds like you are working on your first machine. The CNC Brain is still in Beta testing and, in my opinion, is not be the right solution for someone just getting started in CNC. ...
I read in another thread that you can use a commputer monitor with the Anilam controller since it's PC based. Not sure if thats true.
CNC Brain Beta tester here...
I have a 5'x10' CNC router (with steppers) that I salvaged and rebuilt this year. I am slowly integrating the Brain into the existing system. Not permanent yet as,...
CNC Brain Beta tester here...
I have a 5'x10' CNC router (with steppers) that I salvaged and rebuilt this year. I am slowly integrating the Brain into the existing system. Not permanent yet as,...
Bruce,
Brain came today.
I was thinking it would be very nice to incorporate a tangential knife setting like Mach 3 has.
Cheers,
Dan
Bruce,
Brain came today.
I was thinking it would be very nice to incorporate a tangential knife setting like Mach 3 has.
Cheers,
Dan
Just placed my order. Anyone out there have one hooked up and running yet?
Cheers,
Dan
Just placed my order. Anyone out there have one hooked up and running yet?
Cheers,
Dan
Sounds good to me. I'm buying one.
Thanks for all the info Bruce.
Cheers,
Dan
Sounds good to me. I'm buying one.
Thanks for all the info Bruce.
Cheers,
Dan
Bruce,
Can you clarify how the physical wiring is setup between an existing closed loop servo system and the Brain?
I have Rutex servo drives, they could be Gecko servos though. There is a...
Bruce,
Can you clarify how the physical wiring is setup between an existing closed loop servo system and the Brain?
I have Rutex servo drives, they could be Gecko servos though. There is a...
I am rebuilding a 5'x10' router table. I have parallel stages on the x axis, a motor on each end of the gantry. I have a limit switch for each motor. I built a circuit to accomodate homing. When...
I am rebuilding a 5'x10' router table. I have parallel stages on the x axis, a motor on each end of the gantry. I have a limit switch for each motor. I built a circuit to accomodate homing. When...
I have a 3 HP Perske spindle and need buy an inverter for it. Is it adequate to match the 3HP spindle with a 3HP inverter, or do I need an inverter that is rated for more HP than the spindle?
...
I have just aquired a KIWA Excelcenter 4 in need of some repair. I am wondering if anyone else at cnczone is using one? I am trying to find any KIWA manuals, schematics and fellow operators.
...
Fanuservicetech,
Thanks for the catalog numbers on the manuals.
I've been looking on line and I've come across the Connecting Manual for Fanuc 10/11/12 manual.
What is the content of the...
I will take delivery of the machine on Wednesday. Everything is an unknown to me right now. I am looking for any documentation, schematics, whatever, to start with. Schematics of the controller...
No problem. I did read the sticky at the top of the forum.
Perhaps someone one could point me in the right direction or send me a PM.
Cheers,
Dan
Hello all.
I have acquired a KIWA Excelcenter 4L Bed Mill with Fanuc 10m controller.
This is my first machine and my first experience with a Fanuc controller.
Needs some work...
I am...
It was really great to meet everyone tonight. Big thanks to our host and NEATman! Wish I could have stayed longer.
Cheers,
Dan
When you turn on the curvature graph in Rhino, how does it look? If it is the way you are exporting the dxf out of Rhino, then bring it back in on another layer and compare the original spline to...
I just read through this entire post with a little fear and some hope. I am slowly putting together the hardware for my first CNC machine and have been trying to absorb and learn as much as I can. ...
I found the PMDX-135 Power Prep Module and was thinking about using this as part of my Power Supply.
http://www.pmdx.com/PMDX-135/index.html
Is anyone using this module that can give me some...