Search:

I just found this thread, was the problem solved? I have a backup of my H400 15m parameters. Can't guarantee everything is the same, but its a good start

I recently bought an Andrychow AFM TAE30N CNC lathe, year 2000, but didn't get any maintenance manuals with it. Does anybody know where I might find such a thing? AFM doesn't seem to reply to...

Hi everybody,
I seem to have a similar issue, in that I recently bought a TC-321N, needs some work, got no manuals with it. Did you locate any, or get them scanned? I could sure use a set if...

Thanks, fanuc3mdripfeed.com has exactly what I want/need. Only 3 times what I'm willing to pay for it! I'm pretty sure those chips are nowhere near that cost, anybody know what they are? My power...

I have a mill with a 3M controller that I'd like to do some upgrades on. I have a few questions if y'all don't mind. What chips were replaced to make it do 3 axis simultaneous? Can this machine...

From the looks of the picture, I also have the exact same mill with the same problem. Everything is intact and wired, came from a school surplus auction for $330, but no software. Does anybody have...

I just picked up a desktop cnc mill and lathe at a school surplus auction. I'm pretty sure they are both sherline, but have been rebranded. They are both supposed to be in working order, but the...

kind of a length URL, but try

http://tool.wttool.com/search?p=Q&ts=custom&uid=956095168&srid=S9-2&nodecode=true&af=&do=search&do=search&w=surface+conditioning+belts


this is the search result...

Try looking for "surface condioning belts". I didn't check enco, but wholesale tool www.wttool.com has them. I personally like the wheels that fit a bench grinder, but that depends on your...

I have a Yam CK-2A with a Fanuc 11T. Its been running fine, but when I switched it on today, I get a generic spindle error (just an LED on the control panel), and then a bubble test error. I shut...

I'm completely new to polishing and surface finishing. Most of what I do is good enough if the mic reads right and it looks OK. I have to make a shaft (which will hopefully turn into a production...

Shouldn't there be some way other than a G92? I don't like using that in a program. During setups I invariably stop in the middle of programs to edit something, and when I restart the program it...

I just got a machine that sounds like its pretty much the same except with a nonworking toolchanger. The tool offsets look like they can be set just by hitting the offset key to key the screen and...

:confused: Can anyone tell me how to set my coordinate system on a Fanuc M3? My operators manual doesn't give any programming info except short definitions (no syntax) of G&M Codes. Everything...

Parameters look the same. 0000 is setting parameter, but I don't know what that means. 0014 sets 20A/RS232. 0068 sets Baud rate. I have a complete parameter list. If I get them set the same, how...

I found a diagram in the electric circuit diagram manual. (I'm glad that came with it, even if this info doesn't help) The connector labeled RS-232 into the control (not the cable from the reader)...

Mainboard is back and completely functional!!! Thanks again to everyone for your input. Now I'd like to know a little about communicating with the Fanuc M3 control. The old tape reader is still...

I just talked to TIE again and they confirmed the problem is still in the PCB. They said the error showed up intermittently when testing/fixing and after a week of testing without it showing up...

Just got this board back from Tennessee Industrial Electronics, they rebuilt and tested the board for me. The board had some visible damage that obviously had to be fixed, which is a good thing,...

I'm pretty new to this sort of thing, and pages are missing from some of my manuals, so bear with me. The Main PCB would be the one in the door (probably different for each machine) that the encoder...

I recently bought a Yuasa Enshu Accu-mill with a Fanuc 3m controller. When I fired it up the first time, I got a servo error 34 (z axis). Looked in the manual and found it meant the encoder cable...