Search:

Hi All
I'm looking for a operators manual for an LNS Sprint barfeed fitted on a Mori Seiki ZT2500 Lathe

Hi Scurr,
Depending on what version of edgecam you are using, you should be able to create geometry from the outside shape of the model, then in stocks and fixture it will ask how you wish to create...

M62 does not work as it assigned to another function.

We have a DMG MORI NHX5000 horizontal mill with a M730BM system and I need some info on the Pallet change procedure in memory mode ie How is it called in the Program so that the machine knows which...

Morning all
Does anyone have info on cutting speeds and tooling for machining FR4 composite material?
I want to machine 105 x 19mm holes in a 12mm x 250mm x 250mm plate on a Mori Duracentre...

Try holding the the overtavel release while moving the axis with the handwheel in x 10 increments.

Hi All,
Managed to get the flash card to drip feed. Thanks to all.

Hold 2ndLS switch on while trying to move with handle.

Put Machine into handle mode x 10 and move axis this way

I have a large program that I want to drip feed from flash memory card to a mori seiki NH4000 Machine with a Fanuc MSG-501 system, does anyone know what settings need to be changed for this to be...

Hi All
I want to run a complex component on my Mori NH400 mill using the memory card to drip feed the program as the machine memory is not large enough to take the program, does anyone know the...

Does anyone have an edgecam post processor for a Bridgeport Quaser MF400C with a Siemens Sinumerik 8282D control.

Parameter 996- Bit 5 has to be 1 for geometry offsets.
parameter 997- Bit 6 has to be 1 for tool nose radius compensation

Hi Chopit

Make sure you are using G94 feed per minute, and not G94 feed per rev.

Hi, all

Iam trying to spiral mill using a Fanuc 15M control.
The program is written as shown in manual starting at X0 Y100.0, finishing at X0 Y-30.0 with 20.0mm decreasing radii intervals.

G0...

Hi All
Does anyone have a list of M codes for Mori Seiki ZT2500 Y with a
Fanuc 18iTA system.

Hi Geof,

Managed to produce the reversing leadscrew after a lot of tool trails and program editing.

The G32 cycle worked very well on the Mori Seiki SL15 machine. The main problem was...

Hi Geof,

I have programmed our Mori Seiki using G32 keeping the tool in contact with the material at all times and it is looking good in trial cuts.
The thread is 30mm dia. 3mm wide X 3mm Deep 11...

Hi,

Has anyone cut a reversing leadscrew on a cnc lathe with fanuc Control.

Has anyone cut a reversing leadscrew on a CNC machine? I would like to know the technology involved.

Hi,

Do not use X for dwell time, use either P1000 = 1 second
or use U1.0 = 1 second.

Cheers John.

Make sure the Hydraulics are switched on after power up.

Try Inputting T0100 . Check parameter 387 is set at 360000. best of luck. If this fails try inputting T9900 in

This attachment is a rough turning cycle for Fanuc OT control.

Alternate flank cutting can only be produced on Fanuc FS 15 format ie 1 line canned cycle.
OT system with 2 line cycle will cut on 1 flank only.

You cannot use A60 in 2 line cycle.

John

Here is a program for threading 3-1/8- 8UN

To use staggered cutting the program must be in Fanuc FS15 tape format.
G0 X80.0 Z5.0
G76 X75.52 Z *** K1800 D400 F3.175 A60 P2

X= Core diameter...

Try using controller compensation you do not have to machine a tapered hole if you use an NPT thread milling cutter.